Investigation into Changes of Microstructure and Abrasive Wear Resistance Occurring in High Manganese Steel X120Mn12 during Isothermal Annealing and Re-Austenitisation Process. [PDF]
Materials (Basel), 2022 Hadfield steel, under unit pressure conditions, strengthens itself by forming a high density dislocation structure, which results in increased resistance to dynamic impact wear.
Dziubek M +3 more
europepmc +2 more sources
Tuning the mechanical properties and degradation properties of polydioxanone isothermal annealing. [PDF]
Turk J Chem, 2020 Polydioxanone (PPDO) is synthesized by ring-opening polymerization of p-dioxanone, using stannous octoate as the catalyst. The polarized optical micrograph (POM) shows thes pherulite growth rate of PPDO decreases with an increase in the isothermal ...
Liu X +6 more
europepmc +2 more sources
Crystallization Kinetics Analysis of the Amorphouse Mg72Zn24Ca4 Alloy at the Isothermal Annealing Temperature of 507 K. [PDF]
Materials (Basel), 2020 This paper presents tests of metallic glass based on Mg72Zn24Ca4 alloy. Metallic glass was made using induction melting and further injection on a rotating copper wheel.
Lelito J.
europepmc +2 more sources
Post-Process Effects of Isothermal Annealing and Initially Applied Static Uniaxial Loading on the Ultimate Tensile Strength of Fused Filament Fabrication Parts. [PDF]
Materials (Basel), 2020 Fused filament fabrication (FFF) is one of the most popular additive manufacturing (AM) techniques used to fabricate polymeric structures. However, these polymeric structures suffer from an inherent deficiency of weak inter-laminar tensile strength ...
Rane R +5 more
europepmc +2 more sources
MATERIALS TRANSACTIONS, 2020 Japan The rate-controlling process of compound growth in the Cu-clad Al (CA) wire was metallographically examined in the temperature range of 483 543K (210 270°C). CA wires were prepared by a wire drawing technique, and then isothermally annealed for
Takeshi Kizaki, M. O, M. Kajihara
semanticscholar +1 more source
Morphological changes of the PVD coatings after isothermal annealing
IOP Conference Series: Materials Science and Engineering, 2020 The main of this work is to investigate the impact of the isothermal annealing on the structure and morphological changes on the PVD hard coatings.
P. Babincová +3 more
semanticscholar +1 more source
Understanding Homogeneous Nucleation in Solidification of Aluminum by Molecular Dynamics Simulations [PDF]
, 2017 Homogeneous nucleation from aluminum (Al) melt was investigated by million-atom molecular dynamics (MD) simulations utilizing the second nearest neighbor modified embedded atom method (MEAM) potentials.
Baskes, Michael I. +2 more
core +3 more sources
Study on Spheroidizing Annealing Process of 20CrNiMo Steel
Teshugang, 2022 The subcritical spheroidization annealing, ordinary spheroidizing annealing, and isothermal spheroidizing annealing heat treatment process experiment on 20CrNiMo steel are carried out. By means of optical microscope and brinell hardness tester is carried
柳萍 +5 more
doaj
Fluctuation of the Solute Concentration in Al Rich Al-Zn Alloys [PDF]
, 1978 Several Al-Zn alloys containing 0.041-4.4 at % Zn were studied by means of measurements of electrical resistivity. The results obtained are as follows : (1) The electrical resistivity increases when the specimen is annealed at temperatures higher than ...
Kanadani, Teruto +2 more
core +1 more source
Journal of Applied Research on Industrial Engineering, 2017 AISI H13 tool steel is applied widely to produce many kinds of hot work dies, such as forging dies, extrusion dies, die-casting dies and so on. The successful employment of metal in engineering application relies on the ability of the metal to meet ...
Ubeidulla F. Al-Qawabeha
doaj +1 more source