Results 61 to 70 of about 17,460 (261)
Journal of Advanced Research, 2019 Since AA2060-T8 was introduced in the past few years, investigating the mechanical response, fracture mechanisms, and anisotropic behaviour of AA2060-T8 sheets under high strain rate deformation has been crucial.
Ali Abd El-Aty +5 more
doaj +1 more source
Advanced Healthcare Materials, EarlyView.ABSTRACT The ascent of novel alternative methods in drug development spotlights the dual needs for improved biological fidelity to in vivo, along with reproducibility, especially in regulatory applications. The need for pre‐clinical models of patient‐derived endometriosis lesions motivates the development of a vascularizable, completely synthetic ...
Lauren Pruett +7 more
wiley +1 more source
Advances in Magnesium‐Based Thermoelectrics: A Critical Review
Advanced Materials, EarlyView.Magnesium‐based thermoelectric materials have emerged as promising candidates for low‐to‐mid‐temperature energy conversion due to their abundance, low cost, and competitive performance. This review summarizes recent advances in Mg3X2, MgAgSb, and Mg2X systems, covering transport mechanisms, fabrication strategies, stability challenges, and device ...
Li‐Min Zhang +5 more
wiley +1 more source
Mechanical Engineering Journal, 2016 FEM simulation for the orthogonal cutting of Ti-6Al-4V alloy was investigated. Johnson-Cook's model was used for a flow stress equation of material. Rigid-plastic analysis was carried out using DEFORM-2D and AdvantEdge which were commercial software.
Makoto NIKAWA +3 more
doaj +1 more source
Influence of Carbon Nanoparticles on Electrically Induced Wear of Grease‐Lubricated Steels
Advanced Materials Interfaces, EarlyView.When an electric current enters a pair of rubbing surfaces, enormous damage takes place. In this research, how such damage occurs in the presence of protective grease and the mitigation with added carbon nanoparticles, were investigated. It was discovered that those particles regulate transport and interfacial electrical stability of the grease ...
Mohammad Humaun Kabir +6 more
wiley +1 more source
Strain rate behaviour of multi-phase and complex-phase steels for automotive applications
EPJ Web of Conferences, 2012 A combined study on the mechanical behaviour of multi-phase 800 high yield strength steel (MP800HY) and complex-phase 800 steel (CP800) is carried out under tensile loads in the strain rate range from 0.001s−1 to 750s−1. Quasi-static (0.001s−1) tests are
Singha M.K. +3 more
doaj +1 more source
Advanced Materials Technologies, EarlyView.The article overviews past and current efforts on caloric materials and systems, highlighting the contributions of Ames National Laboratory to the field. Solid‐state caloric heat pumping is an innovative method that can be implemented in a wide range of cooling and heating applications.
Agata Czernuszewicz +5 more
wiley +1 more source
Chemically Doped Conductive Polymers for Wearable Health Monitoring
Advanced Materials Technologies, EarlyView.Among conductive polymers, poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS), polyaniline (PANI), and polypyrrole (PPy) are the most studied and applied. Chemical doping significantly boosts intrinsic conductivity and mechanical robustness.
Mengdi Zuo +5 more
wiley +1 more source
State of stress of a hull structure rammed by the bow of another vessel
Annals of "Dunărea de Jos" University of Galaţi: Fascicle XI Shipbuilding, 2016 The study of structural strength of the hull structure is essential to determine the safety and integrity of the ship, in case of collision. The objective of this work is to study the impact loading of a ship bow on a strengthened plane structure, using ...
Mădălina Prodan +2 more
doaj