Results 31 to 40 of about 4,165 (113)
Anniversaries of Croatian Metallurgy
Metalurgija, 2022 The goal of this work is to give an overview in future tense Monograph „Anniversaries of Croatian Metallurgy“: - The Foundation and Development of Croatian Metallurgical Society (CMS) from the Society of Engineers and Technicians of Steelwork Sisak ...
Ilija Mamuzić
doaj
Techno-economic method for evaluation and selection of flexible manufacturing systems (FMS) [PDF]
, 2012 To find best FMS solutions, experts use numerous multicriteria methods for evaluation and ranking, methods based on artificial intelligence, and multicriteria optimization methods.
D. Lukić +4 more
core
Research on deformations which appear in within the metal structures of mining equipment [PDF]
, 2014 Metal structures of the mining equipment are made of a steel with good weldability and mechanical characteristics corresponding and namely St 52.3 steel that allows the use of these metal structures in heavy duty. Metal structures of the mining equipment
D. Dobrotă, G. Paraschiv
core +1 more source
Istraživanje promjena raspodjele i brzine deformacije u okolini prijeloma s videoekstenziometričkom metodom [PDF]
, 2010 The paper deals with the strain distribution and the strain rate of material in the surroundings of its fracture. Three steels applied in the automotive industry (DP - dual phase steel, microalloyed steel HR 45 and IF - interstitial free steel) were used
M. Mihaliková
core +1 more source
Zona utjecaja topline kod navarivanja kromovog ledeburitnog čelika [PDF]
, 2010 Tools get failured during work; wear is a major factor that contributes to failures. Damaged tools are replaced or filed. This paper describes typical changes that occur in the heat affected zone of tool (HAZ), which was repaired by surfacing with a TIG ...
L. Kosec, M. Tonkovič Prijanovič
core +1 more source
Utjecaj parametara indukcijske elektro peći na brzinu masenog prijenosa u tekućoj fazi [PDF]
, 2012 This article is an analysis of the results obtained under the tests aimed at determination of the influence exerted by the current frequency of an induction furnace on the mass transfer coefficient for liquid metallic phase.U radu su analizirani ...
B. Oleksiak +3 more
core +1 more source
Metalurgija Journal 2022 y – List of Authors and Co-authors
Metalurgija, 2023 On the occasion of sixty years ( 1962-2022 ) of published Metalurgija Journal Bibliography has published all Authors, Co-authors (scientists, experts in the field of metallurgy and other relevant branches, from 40 countries, ie. 5 continents) with name/surname and Numbers ( 1-3008 ) of papers when are published – a total of 3558 Authors, Co-authors ...
openaire +1 more source
Numerical simulation in roll pass design for bar rolling [PDF]
, 2015 The application of finite element simulation to the problem of roll pass design for round bar rolling is considered. Two roll pass sequences were developed by analytical methods and then optimized using 2.5D Finite Element Method (FEM).
Aksenov, Sergey A. +3 more
core
Materials on dies for pressure die casting [PDF]
, 2012 In the contribution the stress of die materials of thermal fatigue is defi ned and material life is derived theoretically and compared with the measured values.
E. Ragan +3 more
core
Sixty years of the publishing of Metalurgija Journal, 1962-2022
Metalurgija, 2023 The goal of the work is give whole the description history, organizations of Journal acctivies and achiewements of Journal from 1962 since 2022y, with this including List of Boards and Co-worker, were publishing total papers 3 008 ie. 2 721 Scientific and Technical and 287 Contributions, total 3 558 Authors and Co-authors from over 40 Countries. On the
openaire +2 more sources