Results 71 to 80 of about 13,476 (127)
Jurnal Riset Industri Hasil Hutan, 2011 The utilization of acacia and kelampayan wood as plywood materials were done. There are two kinds of treatments with two cores samples. Wood core with thickness 2 mm and 3 mm with the spreading rate of adhesive 150 gr/m2, 200 gr/m2 and 250 gr/m2. Resuls showed that the water content of plywood are 9,01% - 14,29% for acacia and 9,17% - 10,58%
openaire +2 more sources
Karakteristik Kayu Lapis dari Bahan Baku Kayu Karet (Hevea Braziliensis Muell. Arg) Berdasarkan Umur Pohon [PDF]
, 2014 Product testing made reference to Standar Nasional Indonesia (SNI) 01-5008.2-1999 Plywood for Structural. Physical properties of plywood includeswater level of plywood withtree ages 20 yearswith average 14,43% ranged from 14,12% until14,67% andfor ...
Setiawan, F. (Fakhdian) +2 more
core
RekayasaPerusahaan kayu lapis ini adalah perusahaan yang memproduksi kayu lapis, blockboard, dan polyester. Dalam proses pembuatan kayu lapis masih ditemukan produk cacat dengan persentase rata-rata dari bulan September 2020 sampai dengan februari 2021 (23,94 ...
Vera Devani, Ifa Fauziah
doaj +1 more source
Kemungkinan Pengendalian Serangga Perusak Kayu pada Kayu Karet dengan Bahan Pelapis
Jurnal Penelitian Hasil Hutan (Journal of Forest Products Research), 2008 Kayu karet (Hevea brasiliensis M11ell. Arg.) sangat rentan terhadap seranggapen1sak terutama b11b11k kayu kering Heterobostrychus aegualis Wat., rqyap tanah Coptotermes curvignathus Ho/mgr. dan rayap kayu kering Cryptotermes cynocephalus Light.
Paimin Sukartana
doaj +1 more source
SIFAT VENIR DAN KAYU LAPIS ENAM JENIS KAYU DARI IRIAN JAYA
Jurnal Penelitian Hasil Hutan (Journal of Forest Products Research), 2017 A study result on the suitability of wood species from Irian Jaya as raw material for veneer and plywood is reported in this paper. This study consisted log peeling characteristic, veneer property, some physical and mechanical properties of plywood (triplex and multiplex).
M I Iskandar +2 more
openaire +1 more source
Pembuatan Balok Dan Papan Dari Limbah Industri Kayu [PDF]
, 2011 Sifat fisik dan mekanik balok dan papan laminasi dari limbah kayu dalam rangka substitusi bahan mebel danpeningkatan nilai tambah telah diteliti. Jenis bahan limbah kayu yang digunakan adalah sebetan kayu durian,kayu plajau dan kayu surian bawang ...
Purwanto, D. (Djoko)
core
PENGARUH LAPISAN KAYU TERHADAP SIFAT BAMBU LAMINA
Jurnal Penelitian Hasil Hutan (Journal of Forest Products Research), 2017 Bambu yang termasuk tanaman cepat tumbuh dan mempunyai daur yang relatif pendek (3-4 tahun) merupakan salah satu sumber daya alam yang cukup menjanjikan sebagai bahan pengganti kayu untuk bahan bangunan.
I M Sulastiningsih +2 more
doaj +1 more source
PEREKAT KAYU LAPIS DARI DAUN LAMTORO (Leucaena Leucocephala)
Jurnal Sains dan Teknologi: Jurnal Keilmuan dan Aplikasi Teknologi Industri, 2016 Adhesives ( adesive ) is a very important material in the plywood industry, the amount of adhesives commonly used in the industry is an adhesive containing chemicals Urea formaldehyde . Urea Formaldehyde is a chemical compound which, when exposed to heat slightly will cause emissions which produce toxic gases that can pollute the air and cause health ...
openaire +3 more sources
Analisis Skala Ekonomis Kerajinan Ukiran Kayu Lapis di Kabupaten Badung [PDF]
, 2017 Growth in the industrial sector would have been affected by business scale in the industry that would tend to indicate the level of efficiency. The purpose of this study was to analyze the influence of labor and capital simultaneously and partially to ...
Sanjaya, I. B. (Ida) +1 more
core
SIFAT VENIR DAN KAYU LAPIS ENAM JENIS KAYU UNTUK HUTAN TANAMAN INDUSTRI
Jurnal Penelitian Hasil Hutan (Journal of Forest Products Research), 2017 The characteristics studied are peeling properties, physical properties of the veneer, gluing properties and some physical and mechanical properties of the plywood (both triplex and multiplex). All logs from 6 wood species could be peeled satisfactorily in cold condition. Veneer of 1.5 mm thickness could be produced at cutting angle
Rodjak Memed +2 more
openaire +1 more source