Results 121 to 130 of about 939,728 (251)
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Control of high harmonic generation in mixed gaseous media
Journal of the European Optical Society-Rapid PublicationsHigh harmonic generation (HHG) in gaseous media provides a robust method for producing coherent extreme-ultraviolet (EUV) radiation and attosecond pulses.
Pablos-Marín José Miguel +2 more
doaj +1 more source
Representación Cartográfica de Datos 3D. Caso práctico. [PDF]
, 2019 Este proyecto tiene como objetivo principal poder representar datos 3D en un visor cartográfico, estos datos se encuentran geográficamente referenciados.El proyecto consta dedos partes,la primera trata del tratamiento de los datos lidar y la ...
Fernández Guitérrez, Patricia Isabel
core
A Workflow to Accelerate Microstructure‐Sensitive Fatigue Life Predictions
Advanced Engineering Materials, EarlyView.This study introduces a workflow to accelerate predictions of microstructure‐sensitive fatigue life. Results from frameworks with varying levels of simplification are benchmarked against published reference results. The analysis reveals a trade‐off between accuracy and model complexity, offering researchers a practical guide for selecting the optimal ...
Luca Loiodice +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study presents an infrared monitoring approach for direct laser interference patterning (DLIP) combined with a convolutional neural network (CNN). Thermal emission data captured during structuring are used to predict surface topography parameters.
Lukas Olawsky +5 more
wiley +1 more source
Proyecto de implantación de una empresa de corte por agua y láser [PDF]
, 2007 El objeto del proyecto comprenderá la constitución de la empresa Laser Water, la implantación y optimización del proceso de corte por agua, y el corte por ...
Ortega Pozo, Daniel
core
Advanced Engineering Materials, EarlyView.The thermal diffusivity of MgO‐C refractories is highly sensitive to sample preparation and processing procedures. In this article, the effects of coking sequence, machining conditions, structural inhomogeneity, and graphite coating application on measurements using laser flash apparatus are systematically investigated.
Luyao Pan +4 more
wiley +1 more source
Bodas de plata del láser [PDF]
, 1985 ln this paper, a short review to the laser history is presented. After some antecedents, taken from Literature and Science, its first steps are reported. Main types and uses follow.
Martín Pereda, José Antonio
core +1 more source
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
Láser verde versus láser verde complementado con resección transuretral protástica bipolar (RTUP bipolar) para el tratamiento de la hipertrofia prostática benigna (HPB) en cuanto a flujometría, volumen residual y síntomas irritativos [PDF]
, 2013 La próstata normal tiene un volumen de 20 ml y se divide en cuatro zonas histológicas, la zona periférica, central, anterior y la zona transicional2. La zona transicional es donde ocurre el fenómeno de hiperplasia de las células estromales, epiteliales y
Reyes Dassum, Samira
core