Results 71 to 80 of about 1,108 (206)
Electromagnetic Shielding Characteristics of Eco-Friendly Foamed Concrete Wall
International Journal of Antennas and Propagation, 2017 The electromagnetic shielding characteristics according to the material composition of foamed concrete, which was manufactured to reduce environmental pollution and to economically apply it in actual building walls, were researched herein.
Sung-Sil Cho, Jin-Man Kim, Ic-Pyo Hong
doaj +1 more source
Thermophysical Properties of the Desulphurization Slags With Various CaS and CaO/Al2O3 Ratio
Advanced Engineering Materials, Volume 28, Issue 10, 20 May 2026.This article investigates how CaS content and the CaO/Al2O3 ratio influence the thermophysical properties of desulphurization slags. Using experimental measurements and thermodynamic simulations, this study reveals complex effects on viscosity, surface tension, and density, providing new insight into slag structure and phase behavior under ...
Eldar Salpagarov +4 more
wiley +1 more source
Advanced Engineering Materials, Volume 28, Issue 10, 20 May 2026.The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert +6 more
wiley +1 more source
Teshugang, 2013 The effect of argon blowing rate (150 ~450 IVmin) and argon blowing location at ladle bottom (ladle center to 3/4 radius of submerged snorkel) on average flow rate at metal-slag interface in 130 t single snorkel furnace with desulphurizing top slag is ...
芮其宣, 成国光
doaj
ON OPTIMIZATION OF STEELMAKING IN ELECTRIC ARC FURNACE AND ITS LADLE TREATMENT IN LADLE-FURNACE
Advanced Engineering Research, 2014 Steelmaking in arc 150-ton electric furnace using iron-rich pellets is considered. It is shown that the melting results are determined by the conditions of the simultaneous processes of the pellet melting and the melt oxidation refining.
Alexander Yuryevich Kem +3 more
doaj +1 more source
Strength performance of low-bearing-capacity clayey soils stabilized with ladle furnace slag. [PDF]
Environ Sci Pollut Res Int, 2023 Espinosa AB +4 more
europepmc +1 more source
Teshugang, 2018 With desulphurizing treatment on low titanium blast furnace slag by blowing CO2method, the rate of removing sulfur from low titanium blast furnace slag is 66.59% ~78.01 % and the residual sulfur content in blast furnace slag is 0.137% ~0.283% , therefore
王宝华 +4 more
doaj
Study on the synthesis mechanism of sodalite, gismondine, and zeolite-P1 zeolite materials from ladle furnace slag and fly ash. [PDF]
Sci Rep, 2023 Ma W, Yi Y, Fang M, Li C, Li J, Liu W.
europepmc +1 more source
, 1994 Slag from Pasminco's lead-zinc smelters, which is rich in zinc, is transferred in thirteen tonne capacity ladles from the blast furnace to the slag fuming furnace. The cycle time is about three hours.
Jenkins, D., Stokes, N.
core
Teshugang, 2006 The P content in molten steel during eccentric bottom tapping of Consteel electric are furnace was ≤0.010% by controlling temperature of molten steel 1560~1590 ℃ and melting with foaming slag in whole period.
夏辉华, 王翔, 袁仁平, 周英豪
doaj