Results 121 to 130 of about 6,731 (266)

Skin‐Like Tri‐Modal Sensors Based on Soft Piezoelectric and Ionic Composites

Advanced Materials Technologies, EarlyView.
Inspired by the multimodal perception of human skin, a soft, skin‐like tri‐modal sensor is presented. The device incorporates an ionically conductive, piezoelectric, elastic composite as its active layer, enabling independent detection of temperature, static strain, and dynamic strain within a single two‐terminal architecture.
Liren Wang, Peter Zalar, Vishva Bhate, Takeo Furukawa, Hidekazu Kodama, Yijun Liu, Yuanyuan Zhou, Chuang Hou, Siyuan Liu, Naoji Matsuhisa   +9 more
wiley   +1 more source

A Sustainable Route for CF/PA6 Composite Waste: From Scrap to Solutions. [PDF]

ACS Omega
Montagna LS, Morgado GFM, de Paula Santos LF, Marini J, Passador FR, Rezende MC.   +5 more
europepmc   +1 more source

Flexible Pressure Sensor With Co‐Optimized Sensitivity and Linearity Based on Gradient Toroidal Microstructures

Advanced Materials Technologies, EarlyView.
A flexible piezoresistive pressure sensor with gradient toroidal CNT/PDMS microstructures is reported. The hierarchical geometry enables sequential electrode contact, achieving a sensitivity of 256.20 kPa−1 and linear response (R2 = 0.99) over 0–1000 kPa.
Rongmei Wang, Ruolin Liu, Ming Lei, Yifan Liu, Fengming Hu, Bing Ji, Chao Peng, Jianyi Luo, Bingpu Zhou   +8 more
wiley   +1 more source

Mechanical Properties of Carbon Fiber and Polyimide Fiber Hybrid Reinforced Polyimide Resin Matrix Composites at Room and High Temperatures. [PDF]

Polymers (Basel)
Lu N, Gao H, Gu Y, Dou H, Li Y.
europepmc   +1 more source

Fully Printed Electrocaloric Heat Pump

Advanced Materials Technologies, EarlyView.
A system based on a flexible printed PEDOT:PSS/P(VDF‐TrFE‐CFE) electrocaloric membrane. The membrane periodically alternates between the cold and hot sides following its electrocaloric cycle and successfully generates a temperature difference. The entire fabrication process is industrially scalable, cost‐effective, and based on widely accessible ...
Adrian Agreda, Florian Le Goupil, Guillaume Payrot, Sokha Khiev, Jean‐David Isasa, Wiljan Smaal, Guillaume Fleury, Georges Hadziioannou   +7 more
wiley   +1 more source

Parametric Study on Scarf Patch Repairs for Shipboard Composite Structures. [PDF]

Materials (Basel)
Liang P, Wang G, Guo Q, Li M, Gong P.
europepmc   +1 more source

The Evolution of Aerosol Jet Printing, A Review: Enhancing Material Versatility and Improvements for Next‐Generation Applications

Advanced Materials Technologies, EarlyView.
Aerosol Jet Printing (AJP) has emerged as a versatile additive manufacturing technique for high‐resolution, conformal, and multi‐material printing. This review highlights advances in printable materials, substrate compatibility, post‐processing, characterization, and process innovations, while critically discussing current challenges and future ...
Chandrachur Chatterjee, Rocco Lupoi, Michael J. Gibbons   +2 more
wiley   +1 more source

Bio-Inspired Cross-Spiral Carbon Fiber Composites: Impact Resistance and Damage Tolerance Under Multiple Low-Velocity Impact. [PDF]

Polymers (Basel)
Jiang L, Li D, Guo Z.
europepmc   +1 more source

Coaxial Melt Electrowriting

Advanced Materials Technologies, EarlyView.
Coaxial melt electrowriting is established to produce dual‐property microfibers with diameters spanning 1.6–29.2 µm. Stable coaxial laminar flow is preserved under electrohydrodynamic thinning, enabling controlled binary and gradient material switching within individual continuous fibers.
Patrick C. Hall, D. Iman von Briesen, Maya Kasteleiner, Gabriela M. Bailey, Diana Ostojich, Harrison W. Reid, Andre Olarra, Benjamín J. Alemán, Simon Luposchainsky, Biranche Tandon, Ramesh Jasti, Paul D. Dalton   +11 more
wiley   +1 more source

Ballistic and drop-weight impact response of SS304 metal mesh embedded woven flax/hemp fiber hybrid composites. [PDF]

Sci Rep
Elayaraja R, Rajamurugan G.
europepmc   +1 more source