Results 211 to 220 of about 6,731 (266)
Some of the next articles are maybe not open access.
Thermal Response in Laminated Composites
ZAMM - Journal of Applied Mathematics and Mechanics / Zeitschrift für Angewandte Mathematik und Mechanik, 1975AbstractA semi‐infinite laminated composite in which the matrix and filler material are aligned parallel to the heat propagation direction is considered. At x = 0, there is applied a harmonic boundary heat flux of y‐periodicity conforming to the periodicity of the layered composite. The Fourier integral solution is decomposed into normal modes.
Manaker, A. M., Horvay, G.
openaire +2 more sources
Laminate theory: macroanalyses of composite laminates
1993It has been shown in chapter 2 that composite materials are manufactured as laminates, consequently in analysing the lamina, the primary aim is to obtain predictions of the average behaviour of the composite from the properties of the components. From the point of view of the mechanical properties of the composite lamina, the area of interest to the ...
openaire +1 more source
Strength of composites repaired by laminating with dissimilar composites
The Journal of Prosthetic Dentistry, 1988D efective composite restorations are usually replaced by completely removing the existing material. However, certain clinical conditions may make it advisable to remove only a portion of the existing restoration before the addition of new material. For example, this technique might be preferred if the existing restoration is near the pulp, retained by
E C, Kao, H G, Pryor, W M, Johnston
openaire +2 more sources
Compression failure of composite laminates
2016This chapter describes the application of a cohesive zone model to estimate the open-hole compressive (OHC) strength of composite laminates and to study the level-ply scaling effect on notch sensitivity. The modeling strategy is to replace the inelastic deformation associated with plasticity or microbuckling with a line crack and to assume some form of
openaire +2 more sources
INTELLIGENT TAILORING OF COMPOSITE LAMINATES
Carbon, 1989Abstract A number of major failure modes in epoxy-matrix composites are reviewed including free edge opening mode delamination, free edge interlaminar shear controlled laminate failure, and impact damage. Methods for suppressing these failure modes through various laminate tailoring techniques are discussed.
openaire +1 more source
Non-conventional Composite Laminates – Clutch Laminates
American Society for Composites 2017, 2017This paper presents the design and manufacturing of novel non-conventional woven composite laminates coined as clutch laminates. Carbon/epoxy clutch laminates are manufactured using prepreg slit tape in an automated fiber placement (AFP) machine. The AFP process allows tailoring the material architecture resulting in innovative structures without the ...
MICHAEL J. L. VAN TOOREN +1 more
openaire +1 more source
Polymers and Polymer Composites, 1996
In order to enhance the stiffness and strength characteristics of wood, hybrid laminates consisting of spruce wood with (a) graphite-epoxy and (b) polyester-glass cloth were made. These hybrid laminates were tested for tension, three-point bending and cantilever bending to estimate the effectiveness of the lamination.
R.M.V. Pidaparti, K. Johnson
openaire +1 more source
In order to enhance the stiffness and strength characteristics of wood, hybrid laminates consisting of spruce wood with (a) graphite-epoxy and (b) polyester-glass cloth were made. These hybrid laminates were tested for tension, three-point bending and cantilever bending to estimate the effectiveness of the lamination.
R.M.V. Pidaparti, K. Johnson
openaire +1 more source
Stress Fields in Composite Laminates
International Journal of Solids and Structures, 1978A new theory is proposed to define the complete stress field within an arbitrary composite laminate. The theory is based upon an extension of Reissner’s variational principle to laminated bodies. Weaknesses in previous laminate theories are discussed and it is demonstrated how these are overcome in the present formulation.
openaire +1 more source