Results 81 to 90 of about 820,605 (274)
Research on Out-of-Plane Bending Test of PVB Laminated Glass Plate with Different Number of Layers
Applied SciencesPolyvinyl Butyral (PVB) laminated glass (LG) with varying numbers of layers is extensively utilized in building structures, and its complex mechanical properties, due to the presence of PVB, pose significant challenges.
Lu Yun +4 more
doaj +1 more source
Role of the Recombination Zone in Organic Light‐Emitting Devices
Advanced Materials, EarlyView.This review summarizes the critical role of the recombination zone in organic light‐emitting diodes (OLEDs). We highlight that broadening the recombination zone in OLEDs based on emissive layers with balanced charge transport and high photoluminescence quantum yields provides a promising route toward achieving both long operational lifetime and high ...
Yungui Li, Karl Leo
wiley +1 more source
Thermoelastic stress analysis of laminated composite materials
, 2009 In this work thermoelastic stress analysis (TSA) is used to obtain quantitative stress/strain data from a variety of multi-directional laminated composites. In order to interpret the thermoelastic signal correctly the source of the thermoelastic response
Sambasivam, Shamala
core +1 more source
Post-Failure Behavior of Point-Fixing Laminated Glass Plates under Out-of-Plane Uniform Pressure [PDF]
This paper presents the results of an experimental and numerical investigation of the mechanical response of undamaged and damaged 2-ply laminated glass plates. Two types of glass plies, thermally toughened and heat-strengthened, coupled with SentryGlas (
Luigi Biolzi +2 more
core +1 more source
Advanced Materials, EarlyView.Molecular doping of conjugated polymers is fundamentally constrained by thermodynamic phase behavior. This Perspective reframes doping efficiency and stability in terms of miscibility limits, binodals, and solvus boundaries, highlighting the role of effective interaction parameters and charge transfer.
Somayeh Kashani +10 more
wiley +1 more source
High Performance Laminated Glass
Challenging Glass Conference Proceedings, 2010 In this contribution we examine the mechanical behavior of laminated glass and show that improvements in performance may be achieved through the use of a stiff, structural, non-PVB, interlayer.
I. Stelzer
doaj +1 more source
Weathering of laminated glass: degradation of interlayer mechanical properties
, 2014 The degradation of polymer due to weathering has been extensively studied in recent years (Martin et al. 2002, Liu et al. 2008, Md Akil et al. 2009, El-Din et al. 1995, Saad et al. 1995).
S Bati +13 more
core +1 more source
Leaftronics: Bio‐Fractal Scaffolds From Leaf Venation for Low‐Waste Electronics
Advanced Materials, EarlyView.“Leaftronics” transforms naturally evolved leaf venation into quasi‐fractal scaffolds for sustainable electronics. Polymer‐infiltrated leaf skeletons can be used to fabricate ultra‐smooth, reflow‐ and thin‐film‐compatible decomposable substrates, while making the same lignocellulose networks conducting results in flexible transparent electrodes.
Rakesh Rajendran Nair +3 more
wiley +1 more source
Advanced Materials, EarlyView.A novel selective laser sintering and graphitization (SLSG) 3D printing technology enables unibody fabrication of compacted insulating structures and conductive circuits in fluidic‐integrated wearable electronics through adaptive photonic modulation.
Li Zhang, Wing Cheung Mak
wiley +1 more source
Performance of SentryGlas-laminated metal-reinforced glass beams at 23, -20 and 60°C
, 2009 To validate the novel concept of laminating a metal reinforcement to a glass beam using a SentryGlas (SG) interlayer, a series of bending tests has been performed at 23, -20 and 60°C on 1.5 m SG-laminated metal-reinforced glass beams. The beams consisted
Callewaert, Dieter +3 more
core