Results 111 to 120 of about 280,675 (318)

A Comprehensive Investigation of Linear and Nonlinear Beam Models on Flexible Wind Turbine Blade Load Calculations

Journal of Marine Science and Engineering
This study was performed to investigate the effects of structural nonlinearity and large deformations on the aeroelastic loads of flexible wind turbine blades.
Xinwen Ma, Xianghua Peng, Jingwei Sun, Yan Chen, Zhihong Huang   +4 more
doaj   +1 more source

ANALYSIS OF LARGE DEFORMATION OF A NONPRISMATIC BEAM

Taiwanese Journal of Mathematics, 1999
zbMATH Open Web Interface contents unavailable due to conflicting licenses.
Hwang, Shin-Feng, Yeh, Li-Rong
openaire   +2 more sources

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

The geometry and thickness of deformation-band fault core and its influence on sealing characteristics of deformation-band fault zones [PDF]

, 2005
Deformation-band faults in high-porosity reservoir sandstones commonly contain a fault core of intensely crushed rock surrounding the main slip surfaces.
Thompson, L.B., Shipton, Z.K., Evans, J.P.   +2 more
core  

Effect of pre-existing crystallographic preferred orientation on the rheology of Carrara marble

, 2014
Localized deformation during high temperature plastic flow is frequently attributed to mechanical weakening caused by grain size reduction and, in some cases, by the development of a crystallographic preferred orientation (CPO).
Kunze, K., Spiers, C.J., Burlini, L., de Raadt, W.S., Experimental rock deformation   +4 more
core   +1 more source

Analysis of laminated shells by a sinusoidalshear deformation theory and Radial Basis Functions collocation, accounting for through-the-thickness deformations [PDF]

, 2011
In this paper, the static and free vibration analysis of laminated shells is performed by radial basis functions collocation, according to a sinusoidal shear deformation theory (SSDT).
Polit, O., C.M.C. Roque, O. Polit, Roque C. C., Roque, C.C., A.J.M. Ferreira, Cinefra M., C. M. C. Roque, Carrera E., M. Cinefra, Cinefra, Maria, Ferreira A. J. M., A. J. M. Ferreira, Roque C. M. C., Ferreira, A.J.M., Carrera, Erasmo, Polit O., E. Carrera   +17 more
core   +1 more source

Consumed by Abdominal Distention

Arthritis Care &Research, EarlyView.
Abimbola Fadairo‐Azinge, James Grenert, Brian Haas, Mary Margaretten   +3 more
wiley   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

Large deformation modelling of tight woven fabric under high air pressure

, 2015
Technical textiles used in airbag are usually in tight structure and subject to high air pressure in through- thickness direction. The pressure can deform fabric with changing its properties such as porosity and air permeability.
Xiao, Xueliang, Lin, Hua, Zeng, Xuesen, Long, Andrew   +3 more
core  

Reduction of degrees of Freedom in three-dimensional ANCF beam of 24-DOF beam element by component mode synthesis

Nihon Kikai Gakkai ronbunshu, 2014
This paper describes how to reduce degrees of freedom for the absolute nodal coordinate formulation (ANCF) of three-dimensional beam made up of 24 degrees of freedom beam elements by applying the component mode synthesis. The stiffness matrix of the ANCF
Kosuke KADOKURA, Nobuyuki KOBAYASHI
doaj   +1 more source