Results 91 to 100 of about 8,497 (257)
Materials & Design, 2018 Aluminum (AA6016) sheets were welded in overlap configuration to investigate the influence of different beam oscillation patterns on the resulting temperature gradient, the local solidification rate and the resulting grain structure and to compare the ...
Christian Hagenlocher +4 more
doaj +1 more source
Ultra Short Pulse Laser Welding of Glass to Metal in the Low Fluence Regime
Laser &Photonics Reviews, EarlyView.Ultrashortpulse laser welding enables precise joining of glass and metal with minimal thermal damage. We introduce the TwoThresholds Criteria to identify suitable laser parameters by combining the nonlinearabsorption threshold in glass with the metalmodification fluence threshold.
Lukas Günther +4 more
wiley +1 more source
Laser assisted arc welding process for dry hyperbaric deep water application [PDF]
, 2013 Hyperbaric Gas Metal Arc Welding (GMAW) is an important technology for repair welding of deep sea pipelines and linking of existing pipeline networks to newer ones through tie-ins and hot-tap welding.
Ofem, Usani Unoh
core
Microstructure and properties of welds between 5754 Al alloys and AZ31 Mg alloys using a Yb:YAG laser [PDF]
, 2014 The authors wish to thank Mr. Henri ANDRZEJEWSKI for his technical assistance in laser experiments. The authors wish to place their sincere thanks to Professor Philippe BOURNOT and Dr.
BANNOUR, Sana +9 more
core +1 more source
Improvements of the welding performance of plasma arcs by a superimposed fibre laser beam
, 2022 Paper 82390DDetails and results of experimental investigations of a laser-supported plasma arc welding process are presented. The particular feature of the realized experimental set-up is the coaxial arrangement of a single-mode fibre laser beam through ...
Schnick, M. +5 more
core +1 more source
Laser beam characteristics of handheld laser beam welding systems
Welding in the WorldAbstract As the use of hand laser beam welding (HLBW) is rapidly increasing even in regulated areas, it is important to use a defined and robust configuration, including parameters, to ensure a reliable process. To this end, it is important to understand the influencing factors and their effects on the resulting properties.
Simon Jahn +7 more
openaire +1 more source
Materials and Corrosion, EarlyView.The localized corrosion behavior of lean duplex stainless steel EN 1.4062 is systematically compared with austenitic and higher‐alloyed duplex grades in natural seawater. A clear resistance ranking is established, highlighting EN 1.4062 as a cost‐effective alternative for limited marine exposure.
Mohammad Hassanzadeh +4 more
wiley +1 more source
Metals, 2020 Deoxidized oxygen free copper C12200, 1 mm in thickness, was welded to 1-mm thick AISI 304 stainless steel with disk laser. The butt-welded joints were produced with different welding parameters.
Miroslav Sahul +5 more
doaj +1 more source
physica status solidi (RRL) – Rapid Research Letters, EarlyView.A two‐step approach based on broad‐beam ion irradiation is demonstrated to produce fine‐tuned self‐assembled surface patterns on MgO(001). It shows an efficient route to modifying the crystalline MgO(001) surface topography in a controlled way, making use of its very specific behavior in terms of both the pattern morphology and patterning dynamics.
Denise J. Erb, Stefan Facsko
wiley +1 more source
Actuation Strategies for Underwater Jet‐Propelled Soft Robots
Journal of Field Robotics, EarlyView.ABSTRACT This review article examines jet‐propulsion mechanisms in underwater soft robotic systems, focusing exclusively on physically fabricated and experimentally validated robots. Covering research published from 2013 to 2025, this study classifies and evaluates jet‐propulsion robots based on their actuation mechanisms.
Angel Kitone +3 more
wiley +1 more source