Results 41 to 50 of about 38,658 (264)
Possible explanations for different surface quality in laser cutting with 1 micron and 10 microns beams [PDF]
, 2012 In laser cutting of thick steel sheets, quality difference is observed between cut surfaces obtained with 1 micron and 10 micron laser beams. This paper investigates physical mechanisms for this interesting and important problem of the wavelength ...
Golubev V. S. +10 more
core +6 more sources
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
Results in Physics, 2018 In this paper, a three dimension heat source is developed in laser heated friction stir welding. The model was calculated by CFD software FLUENT, and the temperature field and flow field of the welding are obtained.
Xinjiang Fei, Zhifeng Wu
doaj +1 more source
International Journal of Lightweight Materials and Manufacture, 2022 The beam oscillation is an innovative technique in laser welding resulting in important enhancement of the weld quality. This study assesses with numerical tools this improvement by investigating the effects of laser power, welding speed and amplitude on
Herinandrianina Ramiarison +2 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.High‐frequency (HF) welding of steel is limited by oxide inclusions that degrade weld quality. This study demonstrates, for the first time, the integration of a nonthermal Ar/H2 dielectric barrier discharge (DBD) plasma jet into HF welding. Local plasma treatment provides effective shielding and in‐situ oxide reduction, resulting in markedly fewer and ...
Viktor Udachin +4 more
wiley +1 more source
Journal of Materials Research and TechnologyThe pores problem is a challenging problem in laser beam welding titanium alloy TC4. Oscillating laser beam welding, as a new welding process, can effectively control the behavior of the molten pool, and is beneficial to the escape of pores, which holds ...
Tianqing Li +5 more
doaj +1 more source
Effect of laser-welding parameters on the heat input and weld-bead profile [PDF]
, 2005 Laser butt-welding of medium carbon steel was investigated using CW 1.5 kW CO2 laser. The effect of laser power (1.2 - 1.43 kW), welding speed (30 - 70 cm/min) and focal point position (-2.5 - 0 mm) on the heat input and the weld-bead geometry (i.e ...
A.G. Olabi +13 more
core +1 more source
Laser welding by focusing multi-laser beams
Optics ExpressThis paper presents a multi-laser beam focusing on laser welding based on a reflective splitting mirror, aiming to improve the stability of the laser welding process and reduce welding defects. By validating the laser welding process on Q235 mild steel using a newly developed multi-focused laser beam, the results show that by increasing the number of ...
Da Li +8 more
openaire +2 more sources
Oxide‐Free Titanium Coatings by Wire Arc Spraying in a Silane‐Doped Inert Atmosphere
Advanced Engineering Materials, EarlyView.A silane‐doped argon atmosphere enables the production of oxide‐free titanium coatings via twin‐wire arc spraying at ambient pressure. This innovative approach eliminates residual oxygen, creating process conditions that prevent oxidation and nitride formation.
Manuel Rodriguez Diaz +4 more
wiley +1 more source
Applied SciencesThe geometry and quality of a weld seam are critical factors in laser beam welding, influencing mechanical performance and structural integrity. Dynamically modulated laser beams provide a precise means of tailoring energy input in high-power laser ...
Karthik Ravi Krishna Murthy +4 more
doaj +1 more source