Results 151 to 160 of about 263,292 (331)

Influence of Heat Treatment on Microstructure and Mechanical Properties at Elevated Temperatures of Nonweldable Ni‐Based Alloy Printed by Fused Filament Fabrication

Advanced Engineering Materials, EarlyView.
The fused filament‐fabricated MAR‐M247 alloy without hot isostatic pressing shows the lowest porosity of 4%. Heat treatment at 1220 °C produces coarse precipitates and carbides. Specimens heat‐treated at 1220 °C exhibit higher tensile strength (683 MPa) and elongation (10%) at room temperature.
Haneen Daoud, Ying Zheng, Agata Kulig, Natalja Agarkov, Esma Mese, Wolfgang Hofmann, Peter Würtele, Uwe Glatzel   +7 more
wiley   +1 more source

Preparation of nickel-based Ni-Ag composite nanoparticles synthesized by DC arc-discharge plasma method and its sintering electrical properties

Cailiao gongcheng, 2020
Ni-Ag nanoparticles were prepared by DC arc-discharge plasma method, using the compacted micron-sized powders of Ni and Ag as the raw targets. The content of Ni in Ni-Ag nanoparticles samples was 70.54%(mass fraction). The particles' sizes were mainly in
WANG Zi-ming, WANG Dong-xing, LU Shan-shan, WANG Xin, DONG Xing-long   +4 more
doaj  

Impact of Hot Isostatic Pressing on Microstructure Evolution and Creep Performance of Powder Bed Fusion–Laser Beam Processed CM247LC

Advanced Engineering Materials, EarlyView.
The influence of Hot Isostatic Pressing (HIP) temperature on the microstructure and creep performance of powder bed fusion–laser beam processed CM247LC superalloy is investigated. Grain growth and γ’ precipitate evolution are characterized following HIP at varying temperatures.
Ahmed Fardan, Johannes Gårdstam, Eva Oscarsson, Håkan Brodin, Eduard Hryha   +4 more
wiley   +1 more source

Cooperative Scattering of a Laser Beam by Shock Produced Plasma

, 1966
Yasukazu Izawa, Masahiro Yokoyama, Chiyoe Yamanaka   +2 more
openalex   +2 more sources

Effects of the Wavenumber Spectrum of a Sea Surface on Laser Beam Reflection [PDF]

, 1979
D. M. Phillips
openalex   +1 more source

Comparative Study of Experimental Methods for Measuring Thermal Properties of 100Cr6 Steel Powders

Advanced Engineering Materials, EarlyView.
This study investigates the thermal properties of 100Cr6 steel in both bulk and powder forms. Measuring the very low thermal conductivity typically exhibited by powders poses significant challenges. To address this, two novel measurement techniques—temperature gradient and finite laser pulse response—are introduced and evaluated by comparison with the ...
Junsheng Zhuo, Hagen P. Kohl, Dongmei Liu, Lisa Matthäus, Arne Bochmann, Aaron Berger, Sebastian Weber, Stefan Nolte, Stephanie Lippmann   +8 more
wiley   +1 more source

Time Variation of the Rough Ocean Surface and Its Effect on an Incident Laser Beam

, 1969
C. Prettyman, Mary D. Cermak
openalex   +1 more source

Erratum: Electron-beam-excited DFB laser in CdS [PDF]

, 1975
Yoshinobu Aoyagi, Susumu Namba
openalex   +1 more source

Key Trends and Insights in Smart Polymeric Skin Wearable Patches

Advanced Engineering Materials, EarlyView.
Intelligent polymers, which respond to various physical and biological stimuli, are explored for the development of skin wearable patches in biomedical applications. Smart polymers, also known as intelligent or stimuli‐responsive polymers, play a crucial role in the development of advanced wearable patches due to their versatility and softness.
Sergio J. Peñas‐Núñez, Rajat Rai, Miryam Criado‐Gonzalez   +2 more
wiley   +1 more source

TESP: A novel simulation platform on tokamak MHD equilibrium based on harmonic mesh finite difference method

AIP Advances
Tokamak MHD equilibrium plays a crucial role in magnetic confinement nuclear fusion studies. It is the foundation of many hot research topics, such as stability, transport, heating, and current drive by radio frequency waves.
Yuan-Jing An, Yue Liu, Yu Jing, Feng Wang, Yuan-Quan Luo, Yan-Bin Xi, Xue-Feng Yang   +6 more
doaj   +1 more source