Results 111 to 120 of about 848,412 (306)
An experimental study to test a 3D laser Scanner for body measurement and 3D virtual garment design in Fashion education [PDF]
, 2005 Artists, scientists, anthropometrists and tailors have accurately measured the human body with traditional tools, such as tape measures, callipers and accumulated visceral experience for centuries. Due to the progressive acceleration in the quality of 3D
Taylor, Andrew, Unver, Ertu
core
A Workflow to Accelerate Microstructure‐Sensitive Fatigue Life Predictions
Advanced Engineering Materials, EarlyView.This study introduces a workflow to accelerate predictions of microstructure‐sensitive fatigue life. Results from frameworks with varying levels of simplification are benchmarked against published reference results. The analysis reveals a trade‐off between accuracy and model complexity, offering researchers a practical guide for selecting the optimal ...
Luca Loiodice +2 more
wiley +1 more source
A 10-nm Spectral Resolution Hyperspectral LiDAR System Based on an Acousto-Optic Tunable Filter
Sensors, 2019 Hyperspectral LiDAR (HSL) technology can obtain spectral and ranging information from targets by processing the recorded waveforms and measuring the time of flight (ToF). With the development of the supercontinuum laser (SCL), it is technically easier to
Yuwei Chen +8 more
doaj +1 more source
The use of terrestrial laser scanning for measurements in shallow-water : correction of the 3D coordinates of the point cloud [PDF]
, 2015 Although acoustic measurements are a wide-spread technique in the field of bathymetry, most systems require a water depth of at least 2 m. Furthermore, mapping shallow-water depths with acoustic techniques is expensive and complicated.
De Wulf, Alain +4 more
core +1 more source
, 2017 Twenty-one distinct AlxCoCrFeNi alloys were rapidly prepared by laser alloying an equiatomic CoCrFeNi substrate with Al powder to create an alloy library ranging x=0.15-1.32.
Borisevich, Albina +4 more
core +1 more source
Advanced Engineering Materials, EarlyView.This study presents an infrared monitoring approach for direct laser interference patterning (DLIP) combined with a convolutional neural network (CNN). Thermal emission data captured during structuring are used to predict surface topography parameters.
Lukas Olawsky +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The thermal diffusivity of MgO‐C refractories is highly sensitive to sample preparation and processing procedures. In this article, the effects of coking sequence, machining conditions, structural inhomogeneity, and graphite coating application on measurements using laser flash apparatus are systematically investigated.
Luyao Pan +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
UAV/UAS Photogrammetry for Use in Cadastral Surveying [PDF]
The International Archives of the Photogrammetry, Remote Sensing and Spatial Information SciencesThe potential of unmanned aerial vehicle (UAV) or unmanned aerial systems (UAS) photogrammetry for use in cadastral surveying tasks was explored as part of a research collaboration with the HafenCity University Hamburg and the Schleswig-Holstein State ...
T. P. Kersten +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source