Results 141 to 150 of about 6,775,431 (345)
, 2017 Terrestrial laser scanning (TLS) is capable to be a reliable deformation monitoring device with high-precision for concrete composite structures. Measurements based on TLS for an arch structure with monotonic loading is carried out.
Hao Yang +3 more
semanticscholar +1 more source
Advanced Engineering Materials, EarlyView.Additively manufactured AlCrFe2Ni2 with contrasting BCC/B2‐dominant and lamellar FCC + BCC/B2 microstructures exhibits the same pressure‐induced BCC/B2 → HCP transformation. Under laser heating at high pressure, HCP is destabilized, and a cubic BCC/B2 + FCC assemblage is recovered, while the lower‐scan‐speed microstructure transforms at a lower ...
Raimundas Sereika +5 more
wiley +1 more source
Impact of Hydrogen Incorporation on Electronic and Magnetic Structure of X2CrNi18‐9 Stainless Steel
Advanced Engineering Materials, EarlyView.Hydrogen uptake in austenitic stainless steel alters both its electronic and magnetic structure. Seebeck measurements reveal hydrogen‐induced shifts in the electronic density of states, while neutron scattering uncovers nanoscale inhomogeneities that grow upon hydrogen incorporation, with the most pronounced effect observed in the PBF as‐built state ...
Torben Tappe +9 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Microstructural evolution of premium rail steel during flash butt welding (FBW), comparing physically simulated heat‐affected zones with actual weld regions. Thermal cycles induce phase transformations and microstructural heterogeneity that influence weld quality and mechanical performance. These findings provide insights into optimizing FBW parameters
Emmanoelle Cintra da Cunha Araújo +15 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.A thermoplastic PMMA‐based photoresin enables high‐resolution DLP printing followed by solvent‐vapor smoothing. The treatment reduces staircase‐induced surface roughness from 2.33 µm to 129 nm and increases visible‐light transmittance from approximately 30% to 80%, providing a route toward transparent PMMA components for rapid prototyping and non ...
Rozhin Heydarpour +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Particle morphology controls the balance between printability and electrical connectivity in low‐temperature AgCu/Ag metallization pastes. Flake‐shaped AgCu particles form extended low‐resistance contacts, whereas spherical particles favor processability at high metal loading. Fine Ag particles further tune void filling and conductive‐network formation
O. Mhirsi +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The present work reports the microstructural, mechanical, and texture evolution of a dissimilar combination laser‐welded maraging steel with 4340 steel. This is important for aerospace applications. The demand for dissimilar welding is growing rapidly with the requirement of efficient and durable joints.
Bharat Behl +3 more
wiley +1 more source
Diode-pumped solid state laser light sources for confocal laser scanning fluorescence microscopy
, 2008 Diode-pumped solid-state lasers (DPSSLs) have been integrated as light sources in confocal laser scanning microscopy (CLSM). The standard argon ion laser at 488 rim is compared with a DPSSL operating at 473 run in terms of noise and CLSM image ...
Stjernström, Mårten, +8 more
core +1 more source
Advanced Engineering Materials, EarlyView.More than 10 000 metal‐coated silicon MEMS cantilevers are fabricated and characterized to build a large‐scale experimental dataset spanning multiple vibrational modes. Machine learning algorithms are benchmarked to predict resonance frequency and quality factor, with ensemble based models achieving accuracy approaching experimental uncertainty.
Sina Zare Pakzad +8 more
wiley +1 more source
Accuracy of a DTM derived from full-waveform laser scanning data under unstructured eucalypt forest: a case study [PDF]
, 2010 A Digital Terrain Model (DTM) is fundamental for extracting several forest canopy structure metrics from data acquired with small-footprint airborne laser scanning (ALS).
Gomes Pereira, L., Gonçalves, G.
core