Results 41 to 50 of about 14,598 (259)
Handbook of Establishing and Maintaining Oxygen‐Free Atmospheres
Advanced Engineering Materials, EarlyView.This study presents a practical framework for creating oxygen‐free atmospheres at ambient pressure using silane‐doped inert gases. The results show that ultra‐low oxygen levels and strongly reduced water content can be achieved through controlled silane dosing, drying systems, and sensor monitoring.
Sascha Jan Zimmermann +3 more
wiley +1 more source
Laser sintered graphene nickel nanocomposites [PDF]
Journal of Materials Processing Technology, 2016 Abstract Laser sintered graphene nickel (Gr–Ni) nanocomposites have been successfully fabricated, with uniform dispersion of graphene nanoplatelets in the nickel matrix. Microstructures and composition of the nanocomposites were investigated by scanning electron microscopy (SEM) and transmission electron microscopy (TEM), energy dispersive ...
Zengrong Hu +8 more
openaire +1 more source
Advanced Engineering Materials, EarlyView.A hierarchical porous copper current collector is fabricated via three‐dimensional printing combined with pressureless sintering to stabilize lithium metal anodes. The interconnected architecture lowers local current density, guides uniform Li deposition within pores, and suppresses dendrite growth.
Alok Kumar Mishra, Mukul Shukla
wiley +1 more source
Scientific Reports, 2022 This study investigates the characteristics of a ceramic phosphor (CP) for the converter of a high-power laser diode-based automobile headlamp synthesized by high-frequency induction heated press (HFP) sintering. The CP prepared by an HFP method exhibits
Seok Bin Kwon +12 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.The wettability of aluminum droplets (Al) on different copper substrates (Cu), where liquid Al spreads on solid Cu surfaces to form a liquid–solid interface, is studied numerically and experimentally. The experimental and numerical results show good agreement in the fast‐spreading regime.
Shan Lyu +8 more
wiley +1 more source
Data in Brief, 2020 The effect of Spark Plasma Sintering (SPS) parameters and Nd:YAG laser welding parameters such as sintering temperature, sintering time, welding power, welding speed, on Vickers hardness mechanical properties of the Weld Zone(WZ) was statistically ...
Ayorinde Tayo Olanipekun +2 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Through direct application of porous transport layer (PTL) on the bipolar plate (BPP) with thermal spraying, the interfacial contact resistance is improved. With the cold gas sprayed BPP–PTL coating system, a proton exchange membrane water electrolysis cell with a cell voltage of Ucell = 1.9 V can be operated up to i = 2.5 A/cm2 in a dynamic mode ...
Kirsten Bobzin +5 more
wiley +1 more source
Powder Bed Fusion via Machine Learning-Enabled Approaches
Complexity, 2023 Powder bed fusion (PBF) applies to various metallic materials used in the metal printing process of building a wide range of complex parts compared to other AM technologies.
Utkarsh Chadha +14 more
doaj +1 more source
Optical Materials: X, 2021 In this work, the role of elaboration parameters (i.e. chemical composition and heat treatments) of Cr:YAG ceramics on their microstructural, optical and laser properties was investigated.
Camille Perrière +5 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.EDX elemental map of the pre‐oxidized MgO–steel cermet anode cross section after electrolysis. The development of inert anodes for aluminum electrolysis remains challenging due to the high corrosivity of cryolite‐based melts at 950°C–1000°C. This study investigates the corrosion and process behavior of a carbon‐free MgO–steel cermet anode derived from ...
Alexander Adamczyk +7 more
wiley +1 more source