Results 111 to 120 of about 244,800 (310)

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

Planar Solid‐State Nanopores Toward Scalable Nanofluidic Integration Based on CMOS Technology

Advanced Engineering Materials, EarlyView.
We present a scalable silicon‐based fabrication strategy for planar solid‐state nanopores to enable their integration with complex nanofluidic systems. Prototype devices demonstrate normal voltage‐current characteristics, good noise performance, and appreciable streaming currents. Our CMOS‐compatible fabrication process offers precise geometric control
Ngan Hoang Pham, Chenyu Wen, Mohammad Hadi Khaksaran, Won‐Yong Lee, Javier Cruz, Klas Hjort, Dongping Wu, Shi‐Li Zhang   +7 more
wiley   +1 more source

Comprehensive Evaluation of Lateral Performance of Innovative Post in Sand

Applied Sciences
Under environmental loads such as wind and earthquakes, piles are subjected to large lateral loads. A foundation system denoted Innovative Post (IP) that is composed of an H-pile shaft and one or two steel plates (paddles) welded to its flanges, has been
Abdelrahman Abouzaid, Mohamed Hesham El Naggar, Osama Drbe   +2 more
doaj   +1 more source

Prediction of Surface Topography Parameters in Direct Laser Interference Patterning of Stainless Steel Using Infrared Monitoring and Convolutional Neural Networks

Advanced Engineering Materials, EarlyView.
This study presents an infrared monitoring approach for direct laser interference patterning (DLIP) combined with a convolutional neural network (CNN). Thermal emission data captured during structuring are used to predict surface topography parameters.
Lukas Olawsky, Marcelo Sallese, Leander Kläber, Clemens Kuhn, Keming Du, Andrés Fabián Lasagni   +5 more
wiley   +1 more source

Pile-Soil Interaction in Unsaturated Soil Conditions [PDF]

, 2014
The degree of saturation has been proven to significantly affect geotechnical engineering designs for foundations. The changes in water content will influence the way the soil behaves, including its strength and stiffness parameters.
Hamilton, Megan
core   +2 more sources

Quantitative Nanofriction Characterization of Corrugated Surfaces by Atomic Force Microscopy

, 2003
Atomic Force Microscopy (AFM) is a suitable tool to perform tribological characterization of materials down to the nanometer scale. An important aspect in nanofriction measurements of corrugated samples is the local tilt of the surface, which affects the
A. Podestà, Adams G., Bhushan B., Cain R., Dedkov G., Derjaguin B., G. Fantoni, Gnecco E., Grafstrom S., Kendall K., Labardi M., P. Milani, Piner R., Podestà A., Podestà A., Stark R., Varenberg M.   +16 more
core   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

EBSD Study of Creep‐Induced Lattice Misorientation in MgO‐Particle‐Reinforced Austenitic Steel Composites

Advanced Engineering Materials, EarlyView.
Creep experiments at 900°C on coarse‐grained steel‐ceramic composites containing recycled magnesia reveal that higher ceramic volume fractions significantly enhance the creep resistance. Detailed EBSD investigations identify subgrain formation in the steel matrix as the dominant deformation mechanism.
Moritz Müller, Amaya Compart, Mahnaz Mehdizadehlima, Serhii Yaroshevskyi, Christos G. Aneziris, Horst Biermann, Anja Weidner   +6 more
wiley   +1 more source

Comparative study on indoor fungi growth incorporated with different antifungal and wall finishings [PDF]

, 2017
Indoor air quality is important to the health and comfort of building occupants. There are many sources of pollutants that can be found in the building. One of the sources of pollutants is fungus. Fungi are present almost everywhere in indoor and outdoor
Subramaniam, Menega
core  

Additive Gaussian Process Regression for Predictive Design of High‐Performance, Printable Silicones

Advanced Engineering Materials, EarlyView.
A chemistry‐aware design framework for tuning printable polydimethylsiloxane (PDMS) for vat photopolymerization (VPP) is developed using additive Gaussian process (GP) modeling. Polymer network mechanics informs variable groupings, feasible formulation constraints, and interaction variables.
Roxana Carbonell, Martha Leach, Hongtao Song, Carolyn Seepersad   +3 more
wiley   +1 more source