Results 31 to 40 of about 566 (119)
Improvement of Starch Extraction Conditions From Agro‐Industrial Residues in Ubá Mango
Starch - Stärke, Volume 78, Issue 4, April 2026.Starch was successfully extracted from the Mango (variety Ubá) seed kernel. Two experimental designs were carried out to improve starch extraction, and results showed that decreasing incubation time and NaHSO3 concentration increased yield. According to the characterization, the kernel starch showed similarity between the Ubá variety and other mango ...
Roseli Lopes da Silva Fontes +6 more
wiley +1 more source
Maderas: Ciencia y Tecnología, 2014 El objetivo de este estudio fue evaluar el efecto de un envejecimiento acelerado mediante rayos ultravioleta y condiciones ambientales controladas sobre la propagación de grietas de debobinado y agrietamiento superficial, al simular las condiciones de ...
Andrés Acevedo +3 more
doaj
Mathematical Prediction for Geometry‐Mediated Cell 3D In‐Growth on Bone Tissue Engineering Scaffolds
Advanced Science, Volume 13, Issue 14, 9 March 2026.This study identifies a fundamental pore size dependent pattern of three dimensional bone marrow derived mesenchymal stem cell (BMSC) infiltration within porous scaffolds, where small pores promote horizontal cellular bridging and large pores facilitate vertical migration.
Xiang Gao +15 more
wiley +1 more source
Maderas: Ciencia y Tecnología, 2014 El objetivo de este estudio fue evaluar el efecto de tres tasas de compresión (TC) en la morfología de grietas de debobinado en chapas de Eucalyptus nitens para la fabricación de tableros contrachapados.
Andrés Acevedo +3 more
doaj
Engineering Reports, Volume 8, Issue 3, March 2026.This study integrates recycled magnesium chips with ceramic fibers to fabricate functionally graded composites exhibiting superior hardness and wear resistance. Machine learning models, particularly LightGBM, accurately predicted wear rates across material zones, reducing experimental effort and demonstrating a sustainable, data‐driven approach to ...
Meenakshi Sudarvizhi Seenipeyathevar +7 more
wiley +1 more source
MetalMat, Volume 3, Issue 1, March 2026.This study experimentally evaluates the performance of eco‐friendly vegetable‐based cutting fluids—coconut, sunflower, and palm oils—during turning of AISI 304 stainless steel under minimum quantity lubrication. Palm oil exhibited superior lubrication and cooling characteristics, yielding the lowest cutting force, temperature, and surface roughness ...
Ranjith Ravindran Nair +3 more
wiley +1 more source
Journal of Orthopaedic Research, Volume 44, Issue 2, February 2026.Migration and cut‐out of DHS, Gamma3, PFNA‐II, and TFNA were compared under dynamic loading in a stable intertrochanteric fracture benchtop foam model and a mesh‐free simulation. No significant differences in force at cut‐out were observed, but simulation revealed that the volumes of damaged bone foam were 15%, 32%, and 25% higher for the Gamma3, PFNA,
Erica Ueda Boles +6 more
wiley +1 more source
Online measurement of veneer lathe checks
, 2015 The present work deals with online lathe checks measurement. It is one of the most critical defects of veneer (leading to handling difficulties, excess of glue consumption, poor veneer surface quality, etc.). It could be characterized by lathe checks depth or frequency but these indicators require tedious measurements of the veneers.
BOUKERI, Asma +4 more
openaire +1 more source
U-NET-based deep learning for automated detection of lathe checks in homogeneous wood veneers
European Journal of Wood and Wood ProductsAbstract Automated detection of lathe checks in wood veneers presents significant challenges due to their variability and the natural properties of wood. This study explores the use of two convolutional neural networks (U-Net architecture) to enhance the precision and efficiency of lathe checks detection in poplar veneers.
Marc, Caroline +3 more
openaire +4 more sources
3D‐Printed Running Shoes for Enhanced Biomechanics and Pressure Distribution: A Review
Advances in Materials Science and Engineering, Volume 2026, Issue 1, 2026.The advent of 3D printing has brought transformative opportunities to the footwear industry, particularly in the design and manufacture of high‐performance running shoes. This review critically explores recent advancements in 3D‐printed running footwear, with a specific focus on enhancing forward propulsion and plantar pressure distribution. Drawing on
James K. Wangui +3 more
wiley +1 more source