Results 81 to 90 of about 136,572 (313)
Mobile Agent-Based Cross-Layer Anomaly Detection in Smart Home Sensor Networks Using Fuzzy Logic [PDF]
, 2015 Despite the rapid advancements in consumer electronics, the data transmitted by sensing devices in a smart home environment are still vulnerable to anomalies due to node faults, transmission errors, or attacks.
Muthukkumarasamy, Vallipuram +2 more
core +1 more source
Advanced Engineering Materials, EarlyView.This article presents the NFDI‐MatWerk Ontology (MWO), a Basic Formal Ontology‐based framework for interoperable research data management in materials science and engineering (MSE). Covering consortium structures, research data management resources, services, and instruments, MWO enables semantic integration, Findable, Accessible, Interoperable, and ...
Hossein Beygi Nasrabadi +4 more
wiley +1 more source
A supercapacitor based enhancement technique for stand-alone surge protection circuits
, 2013 With the International Technology Roadmap for Semiconductors predicting below-25nm feature-size VLSIs, powered by DC power supplies of less than 1V, protection against transients has become mandatory for modern electronic systems.
Kularatna, Nihal +3 more
core +1 more source
Evidence for the Josephson Effect in Quantum Hall Bilayers [PDF]
, 2004 This thesis presents tunneling measurements on bilayer two-dimensional (2D) electrons systems in GaAs/AlGaAs double quantum wells. 2D-2D tunneling is applied here as a probe of the inter-layer correlated quantum Hall state at total Landau level filling
Spielman, Ian Bairstow
core +1 more source
Advanced Engineering Materials, EarlyView.A flexure‐based variable stiffness structure is developed by integrating phase‐change modulation and adhesive interfacial locking of gallium. The design enables a wide stiffness variability, transitioning from soft, flexible behavior to rigid, load‐supporting performance.
Sungjin Kim +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.A hierarchical porous copper current collector is fabricated via three‐dimensional printing combined with pressureless sintering to stabilize lithium metal anodes. The interconnected architecture lowers local current density, guides uniform Li deposition within pores, and suppresses dendrite growth.
Alok Kumar Mishra, Mukul Shukla
wiley +1 more source
Advanced Engineering Materials, EarlyView.Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi +2 more
wiley +1 more source
Performance impairments in single-mode radio-over-fiber systems due to MAC constraints
, 2008 Performance Impairments in Single-Mode Radio-Over-Fiber Systems Due to MAC Constraints Kalantari-Sabet, B.; Mjeku, M.; Gomes, N.J.; Mitchell, J.E.; Lightwave Technology, Journal of Volume 26, Issue 15, Aug.1, 2008 Page(s):2540 - 2548 Abstract ...
Kalantari-Sabat, B. +7 more
core +1 more source
Supercapacitor leakage in energy-harvesting sensor nodes: fact or fiction? [PDF]
, 2012 As interest in energy-harvesting sensor nodes continues to grow, the use of supercapacitors as energy stores or buffers is gaining popularity. The reasons for their use are numerous, and include their high power density, simple interfacing requirements ...
Geoff V. Merrett +3 more
core +1 more source
Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics
Advanced Engineering Materials, EarlyView.Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost +4 more
wiley +1 more source