Results 131 to 140 of about 1,532,249 (292)

Evaluation of Plasticity and Creep Parameters From Tensile Stress–Strain Data for a Range of Strain Rates

open access: yesAdvanced Engineering Materials, EarlyView.
This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley   +1 more source

Bilateral Shoulder Dislocation

open access: yes
This patient suffered a bilateral shoulder dislocation after getting involved in a fight, in which he was held from behind by one of his ...

core  

Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants

open access: yesAdvanced Engineering Materials, EarlyView.
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir   +5 more
wiley   +1 more source

Two Asymmetries between Clitic Left and Clitic Right Dislocation in Bulgarian [PDF]

open access: yes, 2005
The paper discusses some subtle points of the syntax of clitic left dislocation and clitic right dislocation in ...
KRAPOVA I.   +3 more
core  

In Situ Micromechanical Study of Bimodal γ′–γ″ Precipitate Assemblies in Ni–Cr–Al–Nb Superalloy

open access: yesAdvanced Engineering Materials, EarlyView.
A Ni–Cr–Al–Nb superalloy with a bimodal γ′–γ″ precipitate distribution is developed. Composite precipitate assemblies form through heterogeneous nucleation, effectively impeding dislocation motion. Micropillar compression reveals high strength at room and elevated temperatures, governed by precipitate shearing, with coupled faulting mechanisms ...
Ujjval Bansal   +4 more
wiley   +1 more source

On predication, derivation and anti-locality

open access: yes, 2013
This paper pursues the question what the implications of the Anti-Locality Hypothesis could be for the syntax of secondary predication. Focus of the discussion will be an investigation of what their internal structure of small clause complements must ...
Grohmann, Kleanthes K.
core  

Simultaneous anterior and posterior dislocation of hips: a case report and review of literature

open access: yesChinese Journal of Traumatology, 2012
【Abstract】The presence of anterior hip dislocation along with contralateral posterior hip dislocation in the ab-sence of other major traumas is a distinctly rare injury pattern. We report such a case, along with a review of previous cases.
Gupta Vinay   +4 more
doaj  

Literalism and Left Dislocation in the Greek Pentateuch

open access: yesTyndale Bulletin
This article argues that literalism in the Greek Pentateuch is an epiphenomenon of crosslinguistic symmetry. I examine translation of the Left Dislocation construction in the Greek Pentateuch and demonstrate that the translators were aware of its ...
Travis Wright
doaj   +1 more source

Toward Knowledge‐Based Workflows: A Semantic Approach to Atomistic Simulations for Mechanical and Thermodynamic Properties

open access: yesAdvanced Engineering Materials, EarlyView.
Knowledge‐based atomistic workflows are presented for mechanical and thermodynamic properties. By coupling modular simulations with ontology‐aligned metadata and provenance, Fe case studies on elastic behavior, defects, thermal properties, and Hall–Petch strengthening reveal how FAIR, queryable, and reusable simulation data can be generated. Mechanical
Abril Azócar Guzmán   +5 more
wiley   +1 more source

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

open access: yesAdvanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar   +7 more
wiley   +1 more source

Home - About - Disclaimer - Privacy