Results 191 to 200 of about 4,279,935 (303)

Tribological Performance of 60NiTi Alloy Under Varying Contact Conditions and Elevated Temperatures in Linear Reciprocating Sliding

Advanced Engineering Materials, EarlyView.
This study investigates the tribological response of 60NiTi alloy under dry, water‐lubricated and high‐temperature conditions. The alloy exhibits decreasing wear volume and friction with increasing temperature due to the formation of protective oxide layers. The work clarifies dominant wear mechanisms and demonstrates the suitability of 60NiTi for high‐
Anthony Onyebuchi Okoani, Miguel Angel Selles, Maziar Ramezani   +2 more
wiley   +1 more source

Assessing muscle morphology and mechanics: one protocol does not fit all. [PDF]

J Muscle Res Cell Motil
Kissane RWP.
europepmc   +1 more source

Characterization of Nitinol Produced by Laser Powder Bed Fusion for Mechanical Metamaterial Applications

Advanced Engineering Materials, EarlyView.
Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek, Jakub Hurník, Miroslav Šmíd, Ondřej Zobač, Melanie Todt, Daniel Koutný   +5 more
wiley   +1 more source

Quantification of Nasolacrimal Duct Obstruction Length and Its Relationship with Surgical Outcomes. [PDF]

J Clin Med
Ueta Y, Watanabe Y, Tanaka N, Tanaka A.
europepmc   +1 more source

Length-length, Length-weight Relationships and Condition Factor of the Giant Freshwater Prawn Macrobrachium rosenbergii (de Man 1879) Cultured in Earthen Pond at High Density

Asian Fisheries Science, 2016
openaire   +1 more source

EBSD Study of Creep‐Induced Lattice Misorientation in MgO‐Particle‐Reinforced Austenitic Steel Composites

Advanced Engineering Materials, EarlyView.
Creep experiments at 900°C on coarse‐grained steel‐ceramic composites containing recycled magnesia reveal that higher ceramic volume fractions significantly enhance the creep resistance. Detailed EBSD investigations identify subgrain formation in the steel matrix as the dominant deformation mechanism.
Moritz Müller, Amaya Compart, Mahnaz Mehdizadehlima, Serhii Yaroshevskyi, Christos G. Aneziris, Horst Biermann, Anja Weidner   +6 more
wiley   +1 more source

Axial Length Asymmetry in Patients with Unilateral Retinal Detachment. [PDF]

Medicina (Kaunas)
Wang H, Loke JY, Chan WO, Lake S.
europepmc   +1 more source

Piezoresistive Monitoring of Carbon Nanomaterial‐Reinforced Epoxy Composites Under Cyclic and Fatigue Loading: A Review

Advanced Engineering Materials, EarlyView.
Carbon nanomaterial‐reinforced epoxy composites exhibit pronounced piezoresistive behavior, enabling intrinsic damage sensing under cyclic and fatigue loading. This review critically compares carbon nanotube and graphene systems, correlating filler content, percolation threshold, and gauge factor with sensing stability and damage evolution.
J. M. Parente, J. Nunes‐Pereira, A. P. Silva, P. N. B. Reis   +3 more
wiley   +1 more source

Effect of Oxygen Content on Surface and Subsurface Integrity During Turning of Ti–6Al–4V

Advanced Engineering Materials, EarlyView.
This study examines how oxygen content in the ambient atmosphere affects the surface and subsurface properties of Ti–6Al–4V during turning. Results show that oxygen does not influence surface roughness. However, machining in an extremely high vacuum‐adequate atmosphere increases surface hardness by up to 7.8% and induces compressive residual stresses ...
Benjamin Bergmann, Berend Denkena, Hilke Petersen, Florian Schaper   +3 more
wiley   +1 more source

Robot End-Effectors Adaptive Design Method Based on Embedding Domain Knowledge into Reinforcement Learning. [PDF]

Sensors (Basel)
Zhu Y, Zhang T, Lu Y, Yao L.
europepmc   +1 more source