Results 121 to 130 of about 64,568 (266)

Molecular Dynamics Studies of Shape Memory Polymers: From Bead–Spring Models to Atomistic Simulations

Advanced Engineering Materials, EarlyView.
Coarse‐grained (left) and atomistic (right) models of the shape memory polymer ESTANE ETE 75DT3 are shown schematically. The two representations bridge molecular detail and mesoscopic description. Both models capture shape memory behavior, linking segmental mobility and conformational relaxation of anisotropic chains to macroscopic recovery, and ...
Fathollah Varnik
wiley   +1 more source

Nondestructive Testing of Welded Composite Metal Foams

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography (CT) is used to evaluate welded steel–steel composite metal foam (CMF) joints of two density classes. It reports variation in postweld spatial void distribution and correlates it to weld‐induced changes, mechanical performance, and failure within welded CMF panels.
Chinmaya Prerana Inguva, Aman Kaushik, Afsaneh Rabiei   +2 more
wiley   +1 more source

A LIFETIME OF NURSING

American Journal of Nursing, 1998
openaire   +2 more sources

FLIM-based detection of early wound-response signatures suggesting rooting hotspots in Argania spinosa. [PDF]

Tree Physiol
Klaus A, Yechezkel S, Belausov E, Sadot E.   +3 more
europepmc   +1 more source

Influence of Surface Finish on the Tribological Performance of AlTiBN Coatings Deposited on Forming Tools

Advanced Engineering Materials, EarlyView.
Aluminum and nitride coatings are used in industry because they are hard, resist wear, and protect against oxidation. Adding boron can improve friction behavior and other properties. This study tests coatings on surfaces with different finishes. Results show smoother surfaces perform better, while rough ones wear faster, although coatings can reduce ...
Adrián Claver, Iker Alfonso, Eneko Barba, Javier León, José Antonio García, Iñaki Zalakain, Iván Fernández Martínez, Arley García‐Carrero, Christian Almeyda, Daniel Salcedo   +9 more
wiley   +1 more source

Resolving fluorescently labeled species using highly multiplexed spectral FLIM. [PDF]

Sci Rep
Fazel M, Hoseini R, Saurabh A, Xu LWQ, Scipioni L, Tedeschi G, Gratton E, Digman MA, Pressé S.   +8 more
europepmc   +1 more source

Experimental Characterization and Constitutive Modeling of the Effect of Prior Inelastic Strain on the Viscoplastic Behavior of AD730 at 700 °C

Advanced Engineering Materials, EarlyView.
This study shows that superalloys used in aircraft engine disks become much more prone to deformation at high temperatures if they have been strained during manufacturing. This effect increases with the level of prior strain but eventually reaches a limit.
Fabio Machado Alves da Fonseca, Patrick Villechaise, Malik Durand, Arnaud Longuet, Florent Coudon, Loïc Signor, Julien De Jaeger, Dominique Eyidi, Nathalie Bozzolo, Jonathan Cormier   +9 more
wiley   +1 more source

Ultrastable green top-emitting OLEDs approaching BT.2020 enabled by narrowband phosphorescent emitters. [PDF]

Sci Adv
Zhan F, Yuan Y, Xu K, Wu K, She Y, Li G.
europepmc   +1 more source

Low Cycle Repetitive Loading of Ti‐6Al‐4V‐Epoxy Composite Lattice Structures for Enhanced Energy Dissipation and Damage Tolerance

Advanced Engineering Materials, EarlyView.
Composite Ti–6Al–4V–epoxy lattice structures are additively manufactured and epoxy infiltrated for cyclic loading. At low lattice volume fractions, hybridization produces synergistic gains in stiffness and energy dissipation. At higher volume fractions, synergy diminishes, although composites still exceed metallic lattices in specific energy ...
Joey Tallon, Jordan Noronha, Justin Dirrenberger, Andrey Molotnikov   +3 more
wiley   +1 more source

An Experience of a Lifetime [PDF]

Pain Management Nursing, 2005
openaire   +2 more sources