Results 161 to 170 of about 58,785 (356)

MRI geometric distortion: A simple approach to correcting the effects of non‐linear gradient fields [PDF]

, 1999
Serge Langlois, Michel Desvignes, Jean‐Marc Constans, Marinette Revenu   +3 more
openalex   +1 more source

Solid‐State Diffusion and Intermetallic Phase Formation in Roll‐Bonded Mg–Zn Composites With Kirigami‐Patterned Inlay

Advanced Engineering Materials, EarlyView.
Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov, Oleksandr Bobukh, Christian Klose, Florian Nürnberger, Hans Jürgen Maier   +4 more
wiley   +1 more source

Conformal Map Projections for Croatia with Minimal Absolute Linear Distortions

, 2010
U radu je dan usporedni prikaz postojećih konformnih projekcija za Hrvatsku te nove optimalne konformne projekcije po kriteriju najmanje najveće apsolutne linearne deformacije.
Tutić, Dražen, Dražen Tutić
core  

Distortions of the discrete frequency-keyed signals with the linear frequency-modulated impulses in the antenna array

, 2020
Рассмотрены особенности влияния искажений вызванных вращением объекта, изменением его размеров и неидентичностью приемо-передающих трактов антенной решетки на результаты обработки дискретных частотно-манипулированных сигналов в ...
Буйлов, Е. Н., Касперович, М. М., Горшков, С. А., Кондратёнок, В. А.   +3 more
core  

A Simplified Laminar Flow Model for the Pultrusion of Glass Fiber/Polyethylene Terephthalate Commingled Yarns

Advanced Engineering Materials, EarlyView.
A simplified thermoplastic pultrusion model is developed to predict thermal fields in glass fiber/polyethylene terephthalate (GF/PET) composites with reduced computational cost. By combining effective material homogenization, validation against literature data, and Gaussian‐process‐based optimization, the study reveals how heating limits, pulling speed,
Elder Soares, Nadège Bouchonneau, Christian Jochum, Donald Radford   +3 more
wiley   +1 more source

IEEE Instrumentation and Measurement Technology Conference

, 2007
In this paper we set up a framework to deal with nonlinear distortions in a linear modelling framework. The nonlinear system is replaced by a linear system plus a noise source.
Budapest May Linear, J. Schoukens, R. Pintelon, T. Dobrowiecki   +3 more
core  

Polyharmonic distortion modeling of non-linear RF components

, 2020
Bernhard Pichler
openalex   +1 more source

Estimating Ω from Galaxy Redshifts: Linear Flow Distortions and Nonlinear Clustering [PDF]

, 1997
B. C. Bromley, M. S. Warren, W. H. Zurek
openalex   +1 more source

Rafting of Ni‐Based Superalloys Under Multiaxial Load as Understood by Phase‐Field Simulations and Critical Experiments

Advanced Engineering Materials, EarlyView.
Phase‐field simulations coupled with dislocation‐density‐based crystal plasticity modeling reproduce γ′ rafting behavior in single‐crystal Ni‐based superalloys under varied loading conditions. The model captures both macroscopic creep and microscopic morphology evolution, with results matching high‐temperature creep experiments.
Micheal Younan, David Bürger, Gunther Eggeler, Oleg Shchyglo, Ingo Steinbach, Muhammad Adil Ali   +5 more
wiley   +1 more source

Additive Manufacturing of Continuous Fibre Reinforced Composites: Process, Characterisation, Modelling, and Sustainability

Advanced Engineering Materials, EarlyView.
Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley   +1 more source