Results 111 to 120 of about 156,674 (316)
Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys
Advanced Engineering Materials, EarlyView.Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak +3 more
wiley +1 more source
Anti-symmetric motion of a pre-stressed incompressible elastic layer near shear resonance
, 2002 A two-dimensional model is derived for anti-symmetric motion in the vicinity of the shear resonance frequencies in a pre-stressed incompressible elastic plate.
Pichugin, AV, Rogerson, GA
core
ANALYSIS OF NON-LINEAR ELASTIC MATERIAL PROPERTIES OF PVC-COATED PANAMA FABRIC
TASK Quarterly, 2005 The aim of the present paper is to propose a method of laboratory tests to determine non-linear elastic properties of coated Panama fabric. The material parameters are specified on the basis of uniaxial tensile tests in the warp and weft directions ...
ANDRZEJ AMBROZIAK
doaj
Fatigue Crack Initiation and Growth in Nanocrystalline Ni at Multiple Length‐Scales
Advanced Engineering Materials, EarlyView.Overview of miniaturized in situ SEM fatigue setup and resultant fatigue crack growth data for nanocrystalline Ni. The presented study focuses on the analysis of fatigue crack growth rate (FCGR) in focused ion beam‐notched microcantilevers prepared from nanocrystalline (NC) Ni as a model material.
Igor Moravcik +7 more
wiley +1 more source
Variational Approaches to Optimal Control Design for Elastic Body Motions [PDF]
Учёные записки Казанского университета: Серия Физико-математические науки, 2015 Variational and projection statements of an initial-boundary value problem for the direct and inverse dynamics of elastic bodies are proposed. An optimal control problem of 3D linear elastic motions for rectilinear beams with the rectangular cross ...
V.V. Saurin, G.V. Kostin
doaj
A Lightweight Procedural Layer for Hybrid Experimental–Computational Workflows in Materials Science
Advanced Engineering Materials, EarlyView.We unveil a prototype hybrid‐workflow framework that fuses automatedcomputation with hands‐on experiments. Built atop pyiron, a lightweight, parameterized layer translates procedure descriptions into executable manual steps, syncing instrument settings, human interventions, and data capture in real‐time today.
Steffen Brinckmann +8 more
wiley +1 more source
, 2006 Copyright @ 2006 Tech Science PressA quasi-static mixed boundary value problem of elastic damage mechanics for a continuously inhomogeneous body is considered.
Mikhailov, SE
core
Strength analysis of sandwich beams with linear elastic inner layer
Journal of Applied Mathematics and Computational Mechanics, 2022 Koichi Kimura
doaj +1 more source
Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy
Advanced Engineering Materials, EarlyView.A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang +10 more
wiley +1 more source
, 1995 This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.The geometrically nonlinear constant moment triangle based on the von Karman theory of thin plates is first described.
Bangemann, Tim, Bangemann, T.R
core