Results 1 to 10 of about 94,060 (295)
Linear Elastic Fracture Mechanics Characterization of an Anisotropic Shale. [PDF]
Sci Rep, 2018 AbstractThe existence of bedding planes in natural shale formations makes the fracture characterization remarkably complicated. To achieve a further understanding of the anisotropic crack extension behaviors of shale using a linear elastic fracture mechanics approach, four groups of three-point bending tests on Longmaxi shale from southeast Chongqing ...
Luo Y +5 more
europepmc +4 more sources
Pilot evaluation of a fracture process zone in a modified compact tension specimen by X-ray tomography [PDF]
Fracture and Structural Integrity, 2017 In the case of quasi-brittle material, there is a zone of non-linear behaving material, near the crack tip. A major part of this zone forms a socalled fracture process zone (FPZ), where mechanisms of material toughening take place.
J. Klon +5 more
doaj +3 more sources
Experimental and Theoretical Fatigue Crack Propagation in Vitro of the Bovine and Human cortical Bone in Linear Elastic and Elastic-Plastic Fracture Mechanics [PDF]
Engineering and Technology Journal, 2017 This study involved studying fatigue crack propagation in elastic-plastic and linear elastic fracture mechanics LEFM fracture mechanics EPFM for each bovine and cadaveric human cortical bone.
B.O. Bdaiwi, A.F. Abdul-kareem
doaj +1 more source
Nuclear Engineering and Technology, 2022 This paper presents fracture mechanics analysis results for various cracks located at pressurized water reactor pressure vessel nozzle crotch corners taking into consideration constraint effect. Technical documents such as the ASME B&PV Code, Sec.XI were
Jong-Sung Kim +5 more
doaj +1 more source
Basal hydrofractures near sticky patches
Journal of Glaciology, 2023 Basal crevasses are macroscopic structural discontinuities at the base of ice sheets and glaciers that arise by fracture. Motivated by observations and by the mechanics of elastic fracture, we hypothesise that spatial variations in basal stress (in the ...
Hanwen Zhang +4 more
doaj +1 more source
Singular patch method for linear elastic fracture mechanics analysis using isogeometric analysis
Mechanical Engineering Journal, 2022 The singular patch method for isogeometric analysis (IGA) to represent the singular stress behavior in the vicinity of a crack tip for two-dimensional linear elastic fracture mechanics analysis is presented.
Hiroshi OKADA +6 more
doaj +1 more source
Materials & Design, 2020 Experimental fracture mechanics at the microscale became an indispensable tool for understanding and developing advanced material systems. In case of linear elastic fracture mechanics, stringent requirements are typically only warranted for very brittle ...
Ashish Kumar Saxena +4 more
doaj +1 more source
Elastic fracture toughness for ductile metal pipes with circumferential surface cracks [PDF]
, 2017 Surface cracks have long been recognized as a major cause for potential failures of metal pipes. In fracture analysis, the widely used method is based on linear elastic fracture mechanics.
Fu, Guoyang +2 more
core +1 more source
Mode I Fracture Toughness of Graphene Reinforced Nanocomposite Film on Al Substrate
Nanomaterials, 2021 Nanocomposites were prepared by adding graphene nanoplatelets (GNP) into epoxy with a variety of loadings. The thickness of GNPs used in this study was in a range of 1 nm to 10 nm.
Shiuh-Chuan Her, Kai-Chun Zhang
doaj +1 more source
Thermal fracture characteristics of an interface crack subjected to temperature variations
Production Engineering Archives, 2020 Thermal fracture characteristics – the thermal energy release rate and thermal stress intensity factor of a semi-infinite crack at an interface between the two elastic isotropic materials, subjected to the temperature variations, are considered in this ...
Kalinović Saša M. +3 more
doaj +1 more source