Results 51 to 60 of about 140,853 (266)

Review on film cooling of liquid rocket engines

Propulsion and Power Research, 2018
Film cooling in combination with regenerative cooling is presently considered as an efficient method to guarantee safe operation of liquid rocket engines having higher heat flux densities for long duration.
S.R. Shine, S.Shri Nidhi
doaj   +1 more source

Combined Process‐ and Phase‐Field‐Simulation to Predict the Microstructure of Single‐Crystal Ni‐Based Superalloys

Advanced Engineering Materials, EarlyView.
A combined finite element and phase‐field approach predicts the evolution of microstructure during the directional solidification of Ni‐based superalloys. The model reveals how withdrawal rate, temperature gradient, and wall thickness control the dendrite spacing, highlighting the strong effect of surface regions in thin sections where dendrite growth ...
Sean Böhm, André B. Baldissera, Rainer Völkl, Uwe Glatzel   +3 more
wiley   +1 more source

On‐Demand Activation of Thin Alginate Shell Encapsulated Volatile Liquid for Untethered Pneumatic Soft Actuation

Advanced Engineering Materials, EarlyView.
Phase‐changing liquids enable untethered pneumatic actuation in soft robotics but suffer from volatility and storage challenges. This work reports a simple method to encapsulate Novec 7000 within micron‐thin alginate shells via in situ injection and ionic crosslinking.
Rayan A. M. Basodan, Jack Keddie, Byoungyoul Park, Hyun‐Joong Chung   +3 more
wiley   +1 more source

Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger, Lienhard Wegewitz, Wolfgang Maus‐Friedrichs   +2 more
wiley   +1 more source

Population of Nonmetallic Inclusions in Liquid High‐Silicon Electrical Steel in Contact With MgO–C Refractories Based on Recyclates and Environmentally Friendly Binders

Advanced Engineering Materials, EarlyView.
The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert, Matheus Roberto Bellé, Florian Kerber, Dinesh Kumar Gunasekar, Hans‐Jörn Weddige, Christos G. Aneziris, Olena Volkova   +6 more
wiley   +1 more source

Analysis of systems for cooling liquid injection in turbine engine gas flow duct

Авіаційно-космічна техніка та технологія
The subject of this article is a system for cooling liquid injection in gas flow duct of aviation gas-turbine engine (GTE). The goal is to soften the acuteness of contradictions between economic and ecological requirements; ecological requirements and ...
Ruslan Tsukanov, Sergii Yepifanov
doaj   +1 more source

Heat Dissipation for Microprocessor Using Multiwalled Carbon Nanotubes Based Liquid

The Scientific World Journal, 2013
Carbon nanotubes (CNTs) are one of the most valuable materials with high thermal conductivity (2000 W/m·K compared with thermal conductivity of Ag 419 W/m·K).
Bui Hung Thang, Pham Van Trinh, Nguyen Van Chuc, Phan Hong Khoi, Phan Ngoc Minh   +4 more
doaj   +1 more source

Al–Cu Composite Casting of Laser‐Deoxidized Copper: Bonding, Interfacial Chemistry, and Thermal Conductivity

Advanced Engineering Materials, EarlyView.
This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff, Finn‐Lennard Janthur, Sascha Zimmermann, Sarah Seffer, Jörg Hermsdorf, René Gustus, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Christian Klose   +9 more
wiley   +1 more source

Low‐Angle Grain Boundaries and Re‐Segregation in Single‐Crystalline Ni‐Base Superalloys

Advanced Engineering Materials, EarlyView.
This work demonstrates that Re‐segregation at low‐angle grain boundaries (LAGBs) in Ni‐base superalloys is influenced by misorientation angle. Advanced microscopy and atom probe tomography reveal that higher misorientation angles increases Re‐segregation.
Alireza B. Parsa, Aparna Saksena, Alesander Kostka, Pascal Thome, Felicitas Scholz, Alexandre Mussi, Christoph Somsen, Baptiste Gault, Jan Frenzel, Gunther Eggeler   +9 more
wiley   +1 more source

Surface Tension Measurement of Ti‐6Al‐4V by Falling Droplet Method in Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
In this article, the temperature‐dependent surface tension of free falling, oscillating Ti‐6Al‐4V droplets is investigated in both argon and monosilane doped, oxygen‐free atmosphere. Droplet temperature and oscillation are captured with one single high‐speed camera, and the surface tension is calculated with Rayleigh's formula.
Johannes May, Finn‐Lennard Janthur, Lena Kreie, Michael Müller, Sarah Seffer, Nick Schwarz, Jörg Hermsdorf, Thomas Hassel, Stefan Kaierle, Ludger Overmeyer   +9 more
wiley   +1 more source