Results 111 to 120 of about 582,177 (351)

Hybrid Auxetic Architectures: Integrating Curvature‐Driven Design for Enhanced Mechanical Tunability and Structural Performance

Advanced Engineering Materials, EarlyView.
Curvature‐tuned auxetic lattices are designed, fabricated, and mechanically characterized to reveal how geometric curvature governs stretchability, stress redistribution, and Poisson's ratio evolution. Photoelastic experiments visualize stress pathways, while hyperelastic simulations quantify deformation mechanics.
Shuvodeep De, Giovanni Meli, Meysam Khalighian, Anahita Emami   +3 more
wiley   +1 more source

Optimizing Post Friction Stir Welding Heat Treatment in Dissimilar Friction Stir Welded 6061/AlSi10MgMn Joints for Electrical Vehicle Battery Housing

Advanced Engineering Materials, EarlyView.
Microstructural evolution and hardness optimization along the cross‐section of friction stir welded AA6061/AlSi10MgMn joints, for electric vehicle battery housings, were investigated. Postweld aging between 170°C and 220°C enhances hardness uniformity within the nugget zone.
Emanuele Ghio, Emanuela Cerri
wiley   +1 more source

Rolling Contact Fatigue and Static Compression Deformation of UHMWPE thrust bearing in water

MATEC Web of Conferences, 2017
In this study, the rolling contact fatigue tests were performed in order to investigate the effect of thrust load on life of UHMWPE bearings. Furthermore, the static compression tests were performed in order to investigate the effect of static load on ...
Inagaki Masahiro, Fujimura Naoki, Mizobe Koushiro, Kida Katsuyuki, Kashima Yuji   +4 more
doaj   +1 more source

Experimental study of the long-term shortening of reinforced concrete columns under maintaining concentric axial load [PDF]

, 2019
This paper presents the results of an experimental study to measure the shortening of reinforced concrete (RC) columns under long-term maintaining concentric axial load. Long-term axial deformation due to shrinkage and creep of the concrete were recorded
NGUYEN, Manh Hung, TRAN, Long Ngoc, TRAN, The Truyen, TRUONG, Van Quyet   +3 more
core  

Advancing Research on Biomaterials and Biological Materials with Scanning Electron Microscopy under Environmental and Low Vacuum Conditions

Advanced Engineering Materials, EarlyView.
Herein, environmental scanning electron microscopy (ESEM) is discussed as a powerful extension of conventional SEM for life sciences. By combining high‐resolution imaging with variable pressure and humidity, ESEM allows the analysis of untreated biological materials, supports in situ monitoring of hydration‐driven changes, and advances the functional ...
Jendrian Riedel, Lea Dierker, Antoine Eyram Kwame, Kim Nora Wagner, Jonas J. Unterholzner, Jan‐Henning Dirks, Dorothea Brüggemann   +6 more
wiley   +1 more source

Friction and deformation behavior of single-crystal silicon carbide [PDF]

Friction and deformation studies were conducted with single-crystal silicon carbide in sliding contact with diamond. When the radius of curvature of the spherical diamond rider was large (0.3), deformation of silicon carbide was primarily elastic.
Buckley, D. H., Miyoshi, K.
core   +1 more source

Orientation-dependent deformation mechanisms of bcc niobium nanoparticles

, 2017
Nanoparticles usually exhibit pronounced anisotropic properties, and a close insight into the atomic-scale deformation mechanisms is of great interest.
Bian, J. J., Niu, X. R., Wang, G. F., Yang, L.   +3 more
core   +1 more source

Multimodal Mechanical Testing of Additively Manufactured Ti6Al4V Lattice Structures: Compression, Bending, and Fatigue

Advanced Engineering Materials, EarlyView.
In this experimental study, the mechanical properties of additively manufactured Ti‐6Al‐4V lattice structures of different geometries are characterized using compression, four point bending and fatigue testing. While TPMS designs show superior fatigue resistance, SplitP and Honeycomb lattice structures combine high stiffness and strength. The resulting
Klaus Burkart, Jonas Schmidt, Anastasiya Toenjes, Johanna Eisenträger   +3 more
wiley   +1 more source

Study on Torque Distribution of Torque Split Transmission System of Face Gear

Jixie chuandong, 2016
In order to research the influence of installation errors and support deformations on load distribution in the torque split transmission system of face gear,a calculating method for load distribution of torque split transmission system of face gear is ...
Peng Xianlong, Zhang Le
doaj  

Unidirectional Tape‐Based Composites from Hemp and Pineapple Leaf Fiber: Mechanical Performance in Conventional and Bio‐Based Matrices

Advanced Engineering Materials, EarlyView.
The study investigates novel semi‐finished products made of unidirectionally arranged hemp or pineapple leaf fiber‐reinforced composites produced from different matrices. The materials are analyzed in terms of their mechanical and interfacial properties and void content.
Nina Graupner, Raja Bade, Valentin Ackermann, Roja M. Baumann, Corvin Bischoff, Jona F. Ebeling, Oskar Glenz, Marlo Groh, Jonathan Groth, Finja Hiller, Tom Hirschmüller, Felix Menke, Syntcha Ngantchou Lecdou, Mika Ohler, Daniel Rafii Vardiny, Darius Richter, Dario Röper, Henrik Schumacher, Theresa Stein, Benjamin Vorbeck, Elisabeth Wermter, Kay Kölzig, Jörg Müssig   +22 more
wiley   +1 more source