Results 191 to 200 of about 375,588 (279)

Enhancing Wireless Network Efficiency with the Techniques of Dynamic Distributed Load Balancing: A Distance-Based Approach. [PDF]

Sensors (Basel)
Alkalsh MMH, Kliks A.
europepmc   +1 more source

Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials

Advanced Engineering Materials, EarlyView.
Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai, Xinrui Sarah Niu, Zhao Qin   +2 more
wiley   +1 more source

Software defined wireless sensor load balancing routing for internet of things applications: Review of approaches. [PDF]

Heliyon
Isyaku B, Abu Bakar KB, Yusuf NM, Abaker M, Abdelmaboud A, Nagmeldin W.   +5 more
europepmc   +1 more source

Low‐Cost, Large‐Scale Nanoporous Metals by Mechanical Alloying, Oxide Reduction, and Dealloying of Powders

Advanced Engineering Materials, EarlyView.
Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley   +1 more source

A Temporal Deep Q Learning for Optimal Load Balancing in Software-Defined Networks. [PDF]

Sensors (Basel)
Sharma A, Balasubramanian V, Kamruzzaman J.   +2 more
europepmc   +1 more source

Design and Implementation of Dance Online Teaching System Based on Optimized Load Balancing Algorithm.

Comput Intell Neurosci, 2022
Yang Q.
europepmc   +1 more source

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

Facilitating Expedited Drug Approval—the Past, Present, and Future of Clinical Trials for Pediatric Rheumatic Disease

Arthritis Care &Research, EarlyView.
Pamela F. Weiss, Hermine I. Brunner
wiley   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source