Results 281 to 290 of about 44,630 (308)

Gear Contact Model and Loaded Tooth Contact Analysis of a Three-Dimensional, Thin-Rimmed Gear

Journal of Mechanical Design, 2002
This paper performs loaded tooth contact analysis of a three-dimensional, thin-rimmed gear (3DTRG) by presenting a method that combines the mathematical programming method with the three-dimensional, finite element method (3DFEM). Also, a face-contact and whole gear deformation model is used for the 3DTRG.
openaire   +1 more source

Modeling of Helical Gear Power Tri-Branching Transmission Based on Loaded Tooth Contact Analysis

Applied Mechanics and Materials, 2013
According to the principle of tri-branching, a mechanism structural model was developed to analyze the helical gear transmission system. On the base of loaded tooth contact analysis (LTCA), the load transmission error of each gear stage is simulated at the any engagement position, and the fitting curves of the torsion mesh stiffness are obtained, which
Xiao Fang Yang, Zong De Fang, Yong Zhen Zhang, Yuan Fei Han   +3 more
openaire   +1 more source

Loaded multi-tooth contact analysis and calculation for contact stress of face-gear drive with spur involute pinion

Journal of Central South University, 2013
The analytical method based on “Hertz theory on normal contact of elastic solids” and the numerical method based on finite element method (FEM) calculating the contact stress of face-gear drive with spur involute pinion were introduced, and their relative errors are below 10%, except edge contact, which turns out that these two methods can compute ...
Jin-yuan Tang, Yan-ping Liu
openaire   +1 more source

Load Tooth Contact Analysis of Composite Cycloidal Planetary Transmission with Small Tooth Difference

2023 IEEE 12th Data Driven Control and Learning Systems Conference (DDCLS), 2023
Shuhan Zhou, Zhenhua Han, Yunchen Zhou, Yunda Zhao, Hao Wang, Youwu Du   +5 more
openaire   +1 more source

New Calculation Method for the Load Capacity of Bevel And Hypoid Gears Based on Loaded Tooth Contact Analysis

Applied Mechanics and Materials, 2011
At the FZG (Gear Research Centre, Munich, Germany) a research project was carried out to analyze the influence of the hypoid offset on the load capacity of bevel gears by systematic theoretical and experimental investigations. For the experimental investigations two types of bevel gears were designed, one for the pitting tests and one for the tooth ...
Bernd Robert Höhn, Karsten Stahl, Christian Wirth   +2 more
openaire   +1 more source

Loaded Tooth Contact Pattern Analysis for Strain Wave Gear With Non-Elliptical Wave Generator

Volume 10: 2019 International Power Transmission and Gearing Conference, 2019
Abstract This paper presents a new non-elliptical wave generator for strain wave gear to improve its contact pattern quality. The new wave generator has a polynomial profile at one cross section, then crowned along the lead direction. The lead crowning uses a parabolic function with crowning amount controlled by parabolic coefficient ...
openaire   +1 more source

Comparing the contact characteristics of involute gear/eccentric cycloidal gear calculated by various loaded tooth contact analysis models

Forschung im Ingenieurwesen, 2023
L.-C. Chang, Q. Y. Zhuang, S.-J. Tsai, J.-F. Hochrein, S. Landler, M. Otto, K. Stahl   +6 more
openaire   +1 more source

Derivation of tooth stiffness of asymmetric gears for loaded tooth contact analysis

2019
B. Mahr, A. Pogacnik, A. Langheinrich
openaire   +1 more source

Digital twin modeling for loaded contact pattern-based grinding of spiral bevel gears

Advanced Engineering Informatics, 2021
Han Ding, Jinyuan Tang
exaly  

Machine-tool settings driven high-order topology optimization to grinding tooth flank by considering loaded tooth contact pattern for spiral bevel gears

International Journal of Mechanical Sciences, 2020
Han Ding, Jinyuan Tang
exaly