Results 31 to 40 of about 15,216 (261)

Karl Popper and the Mechanisms of Hydrogen Embrittlement

Advanced Engineering Materials, EarlyView.
Representation of the beginning of loss of ductility rather than embrittlement. Small concentrations of hydrogen in a diffusible form within iron are well‐established to harm the mechanical integrity of steels. There are theories that attempt to explain the pernicious role of hydrogen.
H. K. D. H. Bhadeshia
wiley   +1 more source

Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys

Advanced Engineering Materials, EarlyView.
Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak, Olha Zvirko, Rostyslav Leshchak, Hryhoriy Nykyforchyn   +3 more
wiley   +1 more source

Understanding on corrosion mechanism of oxidized AZW800 alloy in 3.5 wt% NaCl solution

Journal of Magnesium and Alloys, 2023
Magnesium alloys are more widely used at higher temperatures. However, it is not well known whether oxide layer, produced at high temperature, could show corrosion protection.
Chunlong Cheng, Qichi Le, Liang Chen, Wenxin Hu, Tong Wang, Baosong Zhu, Xiong Zhou   +6 more
doaj   +1 more source

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

Advanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar, Akash Vyas, Mohammad Aatif Qazi, Nashit Jalal, Maria Ophelia Jarligo, Mostafa Yakout, Jing Liu, André McDonald   +7 more
wiley   +1 more source

Role of complex nonmetallic inclusions on the localized corrosion resistance of wire arc additively manufactured super duplex stainless steel

Journal of Materials Research and Technology
This study investigated the correlation between the MnS·xMnO·yAl2O3·zSiO2·TiN complex inclusions and localized corrosion initiation of the wire arc additively manufactured (WAAMed) super duplex stainless steel (SDSS) part. The results showed that partial
Xianhang Huang, Wenfeng Qiu, Ben Niu, Xiaodong Zou, Linlin Pan, Chi Tat Kwok   +5 more
doaj   +1 more source

Electrochemical Behavior of ZE41 Magnesium Alloy under Simulated Atmospheric Corrosion

International Journal of Electrochemical Science, 2019
The electrochemical measurement technology such as cathodic polarization curves, electrochemical impedance spectroscopy (EIS) and electrochemical noise (EN) were used to study the corrosion behavior of ZE41 magnesium alloy in bulk solution and under thin
Linlin Nie, Xuyang Zhao, Pan Liu, Lulu Hu, Jianqing Zhang, Jiming Hu, Fangfang Wu, Fahe Cao   +7 more
doaj   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Effect of intermetallic compound on the corrosion behaviour of resistance spot welding joints between 5182 aluminium alloy and galvanized DP780 dual-phase steel

Materials Research Express, 2023
Interfacial intermetallic compound (IMC) layer is critical during realizing the galvanic corrosion mechanism and strength degradation of aluminium/steel resistance spot welding (RSW) joints. The effect of IMC layer on the corrosion behaviour of RSW joint
Sai Zhang, Siwei Li, Xianming Meng, Yajun Chen, Congqian Cheng   +4 more
doaj   +1 more source

Defect Evolution and Mechanical Performance of Fused Filament Fabrication‐Manufactured 17‐4PH Stainless Steel Revealed by X‐Ray Computed Tomography

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky, Márk Sárközi, Ibolya Zsoldos, Zoltán Weltsch   +3 more
wiley   +1 more source

Active Corrosion Protection of Sintered AA7075 Aluminum Alloy via Mn Powder Addition

Advanced Engineering Materials, EarlyView.
AA7075 containing Mn‐rich particles is fabricated via spark plasma sintering using AA7075 and Mn powders. Corrosion resistance is evaluated through dip‐and‐dry tests using 0.1 M NaCl (pH 6.0), and mass loss decreases with increasing Mn addition. Mn‐rich particles function as a source of Mn ions, and formation of Mn‐accumulation films on Cu‐containing ...
Ko Ebina, Masashi Nishimoto, Izumi Muto
wiley   +1 more source