Results 141 to 150 of about 2,094,825 (313)
Experimentally-determined external heat loss of automotive gas turbine engine [PDF]
An external heat balance was conducted on a 150 HP two-shaft automotive gas turbine engine. The engine was enclosed in a calorimeter box and the temperature change of cooling air passing through the box was measured.
Meng, P. R., Wulf, R. F.
core +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Application of remote thermal scanning to the NASA energy conservation program [PDF]
Airborne thermal scans of all NASA centers were made during 1975 and 1976. The remotely sensed data were used to identify a variety of heat losses, including those from building roofs and central heating system distribution lines.
Bowman, R. L., Jack, J. R.
core +1 more source
Advanced Engineering Materials, EarlyView.High‐frequency (HF) welding of steel is limited by oxide inclusions that degrade weld quality. This study demonstrates, for the first time, the integration of a nonthermal Ar/H2 dielectric barrier discharge (DBD) plasma jet into HF welding. Local plasma treatment provides effective shielding and in‐situ oxide reduction, resulting in markedly fewer and ...
Viktor Udachin +4 more
wiley +1 more source
Heat shield characterization: Outer planet atmospheric entry probe [PDF]
A full scale carbon phenolic heat shield was fabricated for the Outer Planet Probe in order to demonstrate the feasibility of molding large carbon phenolic parts with a new fabrication processing method (multistep). The sphere-cone heat shield was molded
Disser, E. F. +2 more
core +1 more source
Additive Gaussian Process Regression for Predictive Design of High‐Performance, Printable Silicones
Advanced Engineering Materials, EarlyView.A chemistry‐aware design framework for tuning printable polydimethylsiloxane (PDMS) for vat photopolymerization (VPP) is developed using additive Gaussian process (GP) modeling. Polymer network mechanics informs variable groupings, feasible formulation constraints, and interaction variables.
Roxana Carbonell +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Trace additions of Sn and Sr combined with a two‐step aging treatment are shown to enhance the microstructure and performance of Al–Zr–Sc conductor alloys. Strength and electrical conductivity increase concurrently through accelerated precipitation of fine Al3(Sc, Zr) precipitates and improved dislocation resistance, offering a cost‐effective pathway ...
Quan Shao +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.A hierarchical porous copper current collector is fabricated via three‐dimensional printing combined with pressureless sintering to stabilize lithium metal anodes. The interconnected architecture lowers local current density, guides uniform Li deposition within pores, and suppresses dendrite growth.
Alok Kumar Mishra, Mukul Shukla
wiley +1 more source
Journal of Measurement Science and Instrumentation, 2018 The transient plane source（TPS）method is developed recently to measure the thermal conductivity of materials.In the measurement,the heating power is influenced by the heat which is transferred via the probe electrical leads.This fact further influences ...
WANG Yu-wei, LI Yan-ning
doaj