Results 81 to 90 of about 186,395 (304)
The design of an Fe-12Mn-O.2Ti alloy steel for low temperature use [PDF]
An investigation was made to improve the low temperature mechanical properties of Fe-8 approximately 12% Mn-O 2Ti alloy steels. A two-phase(alpha + gamma) tempering in combination with cold working or hot working was identified as an effective treatment.
Hwang, S. K., Morris, J. W., Jr.
core +1 more source
Experimental Characterization of Electrical Discharge Machining of Aluminum 6061 T6 Alloy using Different Dielectrics [PDF]
, 2019 Electrical discharge machining is a non-traditional machining method broadly employed in industries for machining of parts that have typical profiles and require great accuracy.
Ismail, S. O. +4 more
core +4 more sources
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
The Effects of Alloying Elements on the Corrosion of Rebar Steel in a Chloride Environment
MetalsThe corrosion behaviors in chloride environment of two commercial low-alloy steel bars were studied. Through cyclic wetting tests, accelerated corrosion experiments ranging from 1 to 576 h were conducted on low-alloy bars and original bars.
Jing Yuan +5 more
doaj +1 more source
Determination of low-temperature fatigue properties of structural metal alloys Final report, Jul. 1964 - Aug. 1965 [PDF]
Fatigue testing and determination of low temperature properties of structural metal alloys - aluminum alloy, stainless steel, and nickel ...
Keys, R. D. +2 more
core +1 more source
Fireside corrosion degradation of ferritic alloys at 600°C in oxy-fired conditions [PDF]
, 2014 This paper reports the results of a study carried out to investigate the effects of simulated coal/biomass combustion conditions on the fireside corrosion. The 1000 h deposit recoat exposure (5 × 200 h cycles) was carried out at 600 °C.
Dudziak, T. +4 more
core +1 more source
Sinter hardening low-alloy steels
Metal Powder Report, 1992 The availability of prealloyed steel powders employing molybdenum as the major alloying element offers new levels of compressibility and mechanical properties. When the prealloyed powders are combined with conventional P/M additives such as copper, nickel and graphite, it is possible to develop high strength martensitic microstructures directly from ...
R.J. Causton, J.J. Fulmer
openaire +1 more source
Advanced Engineering Materials, EarlyView.Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar +2 more
wiley +1 more source
The development of creep damage constitutive equations for low Cr-Mo alloy steel and its weldment at low stress [PDF]
, 2013 The ultimate objective of this research project is to develop creep damage constitutive equations for low Cr-Mo alloy and its weldment under low stress (0.2-0.4 yield stress,σ_Y).
Lu, Zhongyu, Xu, Qiang, Xu, Qihua
core
Advanced Engineering Materials, EarlyView.The growing demand for lightweight, nontoxic, and multifunctional gamma shielding materials has intensified efforts to find alternatives to conventional lead and aluminum‐based protectants. In this work, we develop epoxy quartz fabric composites reinforced with cobalt chloride (CoCl2) microparticles, fabricated via hand lay‐up with varying filler ...
Summan Urooge +7 more
wiley +1 more source