Results 291 to 300 of about 796,368 (357)
Some of the next articles are maybe not open access.
, 2020
Based on the experimental results in [1,2], a semi-empirical low-cycle fatigue life prediction model is constructed for a polyamide-6 (PA6) polymer, in which the rate dependence of fatigue life and the effect of ratchetting strain on the life are ...
Jingye Yang +4 more
semanticscholar +1 more source
Based on the experimental results in [1,2], a semi-empirical low-cycle fatigue life prediction model is constructed for a polyamide-6 (PA6) polymer, in which the rate dependence of fatigue life and the effect of ratchetting strain on the life are ...
Jingye Yang +4 more
semanticscholar +1 more source
, 2020
Markl’s pseudo-elastic stress method has been the basis for low cycle fatigue (LCF) evaluation of girth-welded piping connections for decades, which underpins several international codes and standards.
X. Pei, P. Dong, Myung-Hyun Kim
semanticscholar +1 more source
Markl’s pseudo-elastic stress method has been the basis for low cycle fatigue (LCF) evaluation of girth-welded piping connections for decades, which underpins several international codes and standards.
X. Pei, P. Dong, Myung-Hyun Kim
semanticscholar +1 more source
Low cycle fatigue performance of DP600 steel under various pre-straining paths
, 2020The present work concerns the assessment of low cycle fatigue performance of dual phase steel subjected to change in uniaxial pre-strain path. An uniaxial pre-strain of 12.5% in the rolling or transverse direction were imposed on the dual phase steel ...
Bimal Das, Akhilendra Singh, S. Paul
semanticscholar +1 more source
Conventional Fatigue (High- and Low-Cycle Fatigue)
1997It is known that when metals are subjected to fluctuating load, the failure occurs at a stress level much lower than the fracture stress corresponding to a monotonic tension load.1 With the development of the railway in the nineteenth century, the fatigue failure of railway axles became a problem and much attention was given to the understanding of the
Bahram Farahmand +2 more
openaire +1 more source
Effect of nitriding on low-cycle fatigue properties
International Journal of Fatigue, 1997Abstract Nitriding is a thermochemical surface treatment that is often utilized to improve the fatigue strength of mechanical elements. In fact it is well known that, after the treatment, owing to the formation of a nitrided external layer and a field of residual stresses that are compressive on the surface, the high-cycle strength is strongly ...
GUAGLIANO, MARIO, VERGANI, LAURA MARIA
openaire +2 more sources
International Journal of Fatigue, 2019
Powder metallurgy (P/M) nickel-based superalloy FGH96 is widely used for turbine discs in aero-engines. With an increasing trend towards powder metallurgy routes for turbine discs, undesired non-metallic inclusions comparable to the grain size are ...
Dianyin Hu +7 more
semanticscholar +1 more source
Powder metallurgy (P/M) nickel-based superalloy FGH96 is widely used for turbine discs in aero-engines. With an increasing trend towards powder metallurgy routes for turbine discs, undesired non-metallic inclusions comparable to the grain size are ...
Dianyin Hu +7 more
semanticscholar +1 more source
2003
A solution annealed type 316 stainless steel exhibits a uniaxial cyclic stress-strain curve at 550°C ...
J. Yates, M. W. Brown
openaire +1 more source
A solution annealed type 316 stainless steel exhibits a uniaxial cyclic stress-strain curve at 550°C ...
J. Yates, M. W. Brown
openaire +1 more source
Effects of specimen size on fatigue life of metallic materials in high‐cycle and very‐high‐cycle fatigue regimes [PDF]
Fatigue and Fracture of Engineering Materials and Structures, 2016 This paper proposes a new method to investigate the effect of specimen size on fatigue life of metallic materials in high-cycle fatigue and very-high-cycle fatigue regimes in the light of statistical analysis.
Zhang XL(张晓乐) +4 more
exaly +2 more sources
Low cycle fatigue, deformation and fracture behaviour of Inconel 617 alloy
Materials Science & Engineering: A, 2019Inconel 617 alloy is one of the potential materials for high temperature applications such as steam generator super heater, re-heater parts and intermediate heat exchangers in gas cooled reactors.
C. Rao +3 more
semanticscholar +1 more source