Results 191 to 200 of about 658,002 (264)

Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy

Advanced Engineering Materials, EarlyView.
A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang, Aparajita Pramanik, Sandipan Sen, Shubhashis Dixit, Marcel Muench, R. J. Vikram, Daniel Schliephake, Yolita M. Eggeler, Ankur Chauhan, Martin Heilmaier, Alexander Kauffmann   +10 more
wiley   +1 more source

Increasing connectivity through self-complementarity enables permanent porosity in a halogen-bonded organic framework. [PDF]

Chem Sci
Moghadasnia MP, Evans HA, Hippely AS, Sanchez Hernandez JJ, Holm MG, Ponce GG, Martin HR, Mannina RP, Eckstein BJ, Klein RA, Kumar P, Stern CL, Malliakas C, Brown CM, McGuirk CM.   +14 more
europepmc   +1 more source

Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han, Julian M. Rosalie, Jan Radners, Mauro Madia, Philipp von Hartrott, Birgit Skrotzki   +5 more
wiley   +1 more source

Comparison of the Mechanical Properties and Surface Characteristics of Vat Photopolymerization Resin Materials and a Polymethyl Methacrylate Disc Material. [PDF]

Materials (Basel)
Yu F, Kanda R, Hashimoto Y, Suese K, Mitamura K, Kobayashi Y, Kashiwagi K.   +6 more
europepmc   +1 more source

High‐Temperature Nanoindentation of Metals: Assessing Thermal Drift, Frame Compliance, and Chemical Composition Effects on the Reported Mechanical Properties

Advanced Engineering Materials, EarlyView.
Do not let thermal drift and instrument artifacts deceive high‐temperature nanoindentation results. We compare classical Oliver–Pharr and automatic image recognition analyses across steels and a Ni alloy to quantify these effects. Accounting for artifacts reveals systematic softening with temperature, while Cr and Ni additions boost resistance ...
Velislava Yonkova, Steffen Brinckmann, Ruth Schwaiger   +2 more
wiley   +1 more source

Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites

Advanced Engineering Materials, EarlyView.
Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter, Andreas Bezold, Johan Westraadt, Katharina Fiegl, Subham Chattoraj, Benjamin Wahlmann, Carolin Körner, Michael Mills, Mathias Göken, Steffen Neumeier   +9 more
wiley   +1 more source

Impact of Structural Dimensionality on the Optoelectronic Behavior of Lead-Halide Perovskites. [PDF]

Materials (Basel)
Gouadria H, Álvarez J, Capitán MJ.
europepmc   +1 more source

Current Status and Challenges in Data Collection for Aerospace Coatings Deposited by Plasma Spraying

Advanced Engineering Materials, EarlyView.
An innovative approach has been integrated into the GRENAT project to optimize plasma spraying and coating performance. Raw materials are accelerated and melted in the plasma generated by torches, creating coatings. Monitoring sensors collect process data which are combined with ex situ characterization data.
Lila Randriamananjara, Vincent Rat, Quentin Dubreuil, Patrice Valorge, Simon Goutier, Alain Denoirjean, Olivier Messe, Céline Ruelle, Jean‐Philippe Poli   +8 more
wiley   +1 more source

Hygroscopic Behaviour and Diffusion Characteristics of Flexible TPU Materials Fabricated by FDM for Potential Biomedical Applications. [PDF]

Polymers (Basel)
Šimunić N, Kostadin T, Hoster J, Obranović D.   +3 more
europepmc   +1 more source

Optimization of the Production of Rubber Compounds Using Mathematical Models

Advanced Engineering Materials, EarlyView.
Rubber compounds were mixed in a batch internal mixer, and symbolic regression was used to derive mathematical models linking recipe and process parameters to ram path, torque, and mixing quality (incorporation, dispersion, distribution). Subsequent optimization with evolutionary algorithms identified operating conditions that reduce specific energy ...
Anke Bardehle, Andreas Limper, Ulrich Giese, Carlos Lucke, Mario Beiner, Christoph Gögelein, Lisa Leuchtenberger‐Engel, Christian Hopmann   +7 more
wiley   +1 more source