Results 161 to 170 of about 10,979,660 (212)

A Safe and Portable CMUT Array Ultrasonic System for Bubble Sizing in Industrial Silicone Sealing Rings. [PDF]

open access: yesMicromachines (Basel)
He C   +11 more
europepmc   +1 more source
Some of the next articles are maybe not open access.

Related searches:

Design of an Optimal Low Noise Amplifier (LNA) for Signal Boosting

2019 International Conference on Mechatronics, Remote Sensing, Information Systems and Industrial Information Technologies (ICMRSISIIT), 2019
The purpose of a Low Noise Amplifier (LNA) is to amplify received signals to acceptable levels while minimizing noise. The LNA is used in communication systems to amplify very weak signals captured by an antenna. The design of an LNA in Microwave circuits requires a trade-off or careful balance of many important parameters such as Gain, Noise Figure ...
Frank Lemdi Prikutse   +2 more
exaly   +2 more sources

A New Built-In Self-Test (BIST) for a RF Low-Noise Amplifier (LNA)

5th International Conference on Design & Technology of Integrated Systems in Nanoscale Era, 2010
In this paper, we present a new RF built-in self test (BIST) circuit for 865–870 MHz low noise amplifiers (LNAs); The BIST and LNA circuit is designed using 0.35µm CMOS technology. The simple circuit of test that contains a RF peak detectors and two comparators brings high fault coverage.
R. Ayadi, M. Masmoudi
exaly   +2 more sources

Design of a Dual-Band Low Noise Amplifier (LNA) Utilizing Positive Feedback Technique

2006 4th Student Conference on Research and Development, 2006
This paper presents a dual band low noise amplifier (LNA) for 1.8 GHz DECT and 2.4 GHz WLAN applications employing positive feedback technique. This LNA exploits a positive feedback capacitor connected to a conventional cascaded inductive source degenerated LNA whereby the connection of a capacitor determines the operating frequency of the LNA.
Roslina Sidek, Sabira Khatun, S S Jamuar
exaly   +2 more sources

Antenna and low noise amplifier (LNA) co-design

2009 International Semiconductor Device Research Symposium, 2009
In general, circuit designers and antenna designers work independently. The link between antenna and circuit is the conventional characteristic impedance in RF systems, such as 50Ω line in telecommunication circuits, or 75Ω in television systems. Noise matching and power matching are not likely to achieve simultaneously at 50Ω or 75Ω.
null Bo Yang   +3 more
openaire   +1 more source

Design of K-Band Low Noise Amplifier (LNA) Based on Active-Bias

2024 9th International Conference on Integrated Circuits and Microsystems (ICICM)
Qiqi Li
exaly   +2 more sources

A CMOS continuous variable gain low-noise amplifier(LNA) for WLAN applications

Proceedings of the 24th symposium on Integrated circuits and systems design, 2011
In order to attend the exponential growth of wireless communication in portable device market, a demand for flexible RF transceivers has become a major research interest, including those with the ability of communicating in an unpredictable environment, from very weak to highly powered signal levels without losing its functionality.
Augusto Ronchini Ximenes   +1 more
openaire   +1 more source

Design and simulation of high gain PHEMT low noise amplifier (LNA)

2007 International Conference on Computer Engineering & Systems, 2007
This paper presents a 5.8 GHz low voltage, low power, and wide band LNA design using PHEMT transistor. The simulated LNA is a single stage with pi input and output matching circuits. The noise canceling principle and sensitivity analysis is performed for the simulated low noise amplifiers. The simulated results are compared with identical LNA published
Mohamed Rizk, Mohamed Nasar, Alaa Hafez
openaire   +1 more source

Analysis of LNA(Low Noise Amplifier) Susceptibility by EMP Coupled to the Monopole Antenna

The transactions of The Korean Institute of Electrical Engineers, 2019
In this paper, the output waveform of EMP coupled to 10 MHz monopole antenna analyzed by simulation, and the susceptibility of LNA(Low Noise Amplifier) was evaluated. The waveform of EMP coupled to the monopole antenna is a 10 MHz damped sinusoidal waveform, and the peak voltage is about 22 kV.
Jeong-Ju Bang, Chang-Su Huh
openaire   +1 more source

Home - About - Disclaimer - Privacy