Results 151 to 160 of about 92,105 (300)

Thermodynamic Pathways of Nonequilibrium Solidification in Wire‐Arc Additive Manufacturing Fe‐Based Multicomponent Alloy Structures

Advanced Engineering Materials, EarlyView.
Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios, Anthony Gonzalez, Aleksander Aleman, Tyler Dolmetsch, Tanaji Paul, Arvind Agarwal   +5 more
wiley   +1 more source

Tailored Hierarchical Porous Copper Architectures via Three Dimensional Printing and Pressure‐less Sintering for Next‐Generation Lithium‐Metal Batteries

Advanced Engineering Materials, EarlyView.
A hierarchical porous copper current collector is fabricated via three‐dimensional printing combined with pressureless sintering to stabilize lithium metal anodes. The interconnected architecture lowers local current density, guides uniform Li deposition within pores, and suppresses dendrite growth.
Alok Kumar Mishra, Mukul Shukla
wiley   +1 more source

An Assessment in the Heat Gain and Loss Through Opaque Elements in Commercial Buildings in Brazil

, 2012
This paper presents an analysis of the energy performance of commercial buildings in Brazil based on the influence of the thermal transmittance of the external walls and roof.
Melo, Ana Paula, Lamberts, Roberto
core  

Near‐Field Electrospinning Micro‐Printhead Achieves Precise Control of Nanofiber Deposition

Advanced Engineering Materials, EarlyView.
A micro‐printhead for near‐field electrospinning enables reproducible deposition of polymer nanofibers with diameters below 50 nm. Systematic parameter studies uncover the mechanisms linking operating conditions to fiber morphology, paving the way for precise and low‐cost nanoscale 3D manufacturing.As a high‐resolution, cost‐effective, and rapid ...
Han Xu, Dario Mager, Jan G. Korvink
wiley   +1 more source

Air‐Pressure–Actuated Vibroacoustic Metamaterial With Tunable Bandgap: Design, Modeling, and Characterization

Advanced Engineering Materials, EarlyView.
This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal, Michael M. Becker, Sarah C. L. Fischer   +2 more
wiley   +1 more source

Composition‐Tuned Enhancement of the Anomalous Nernst Effect in FeCo–Pt Thin Films on Rigid and Flexible Substrates

Advanced Engineering Materials, EarlyView.
Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi, Hiroyuki Awano, Kenji Tanabe   +2 more
wiley   +1 more source

Assessing the restorative benefits of open rooftop green spaces characteristics using virtual reality and EEG analysis. [PDF]

Front Psychol
Chen Z, Shen Y, Zhu B, Gan KK, Zhou T, Fang Y, Zeng M.   +6 more
europepmc   +1 more source

Evaluating Energy Absorption Performance of Filled Lattice Structures

Advanced Engineering Materials, EarlyView.
Maximum stress must be considered to robustly evaluate energy absorber designs. This approach was applied to compare all types of absorbers in a single Ashby diagram and determine the utility of filling lattice voids with a second material. High‐performance fillers can improve the performance of lattices that are limited by buckling or catastrophic ...
Christian Bonney, William P. King, Iwona Jasiuk   +2 more
wiley   +1 more source

Thermal amplification by large-footprint buildings in cold-climate cities: Implications for urban heat mitigation. [PDF]

Build Environ
Miles V, Esau I, Kuklina V.
europepmc   +1 more source

Creating Ti–Fe α/β Alloys by Diffusion‐Driven Solid‐State Processing

Advanced Engineering Materials, EarlyView.
This study proposes making alloys containing fast diffusing elements that are difficult to produce by ingot metallurgy, by diffusion‐driven solid‐state HIP processing of elemental powders and low‐temperature homogenisation. Here, novel Fe‐Ti α–β alloys are formed having fine α–β lamellae, a small β prior grain size without significant intermetallics ...
Jiaqi Xu, Xun Zhang, Jack M. Donoghue, Albert D. Smith, Rahul Unnikrishnan, Rhys Thomas, Vahid Nekouie, Jie Luo, Dongchen Hu, Michael Preuss, Philip J. Withers   +10 more
wiley   +1 more source