Surface Potential Decay of Gamma-Irradiated Low-Density Polyethylene [PDF]
, 2009 In the present paper the surface potential decay after dc corona charging of gamma-irradiated low-density polyethylene (LDPE) has been studied. The irradiation was carried out in air, nitrogen gas and vacuum to investigate the effect of irradiation ...
Chen, George
core +2 more sources
Nanoscale Analysis of the Interaction Between Cyanoacrylate and Vacuum Metal Deposition in the Development of Latent Fingermarks on Low-Density Polyethylene [PDF]
, 2011 Vacuum metal deposition (VMD) has been previously demonstrated as an effective development technique for latent fingermarks and in some cases has been shown to enhance prints developed with cyanoacrylate (CA) (superglue) fuming.
Sears, V.G. +7 more
core +3 more sources
Modification of Space Charge Pattern and Charge Mobility of Low Density Polyethylene (LDPE) in the presence of Crosslinking Byproducts [PDF]
, 2009 The formation of space charge in Crosslinked Polyethylene (XLPE) cable has always been related to the byproducts such as acetophenone, ?-methylstyrene and cumyl alcohol. In this paper, the argument is to be justified.
Hussin, Nuriziani, Chen, George
core +2 more sources
Decay of Electric Charge on Corona Charged Polyethylene [PDF]
, 2007 In this paper, the surface potential decay of corona-charged low density polyethylene (LDPE) films has been investigated. It has been found that for the same sample thickness the faster decay occurs in the sample with a higher charging voltage.
Zhiqiang Xu +8 more
core +2 more sources
The effect of gamma irradiation on space charge behaviour and dielectric spectroscopy of low-density polyethylene [PDF]
, 2007 The influence of gamma irradiation on low-density polyethylene (LDPE) has been studied through space charge measurement and dielectric spectroscopy. Commercial LDPE film with a thickness of 100µm was irradiated with γ-rays at a dose rate of approximately
Dissado, L. A. +4 more
core +2 more sources
Bubble plastic use in rats hernioplasty: Uso do plástico bolha em hernioplastias de ratos
Heliyon, 2023 Purpose: Despite the high frequency of hernioplasties worldwide, their complications and recurrences are still a challenge to be overcome. The search for prostheses that aim to promote the correction of hernia defects has been a challenge.
Siria da Fonseca Jorge +3 more
doaj +1 more source
ELECTROSTATIC CHARGE GENERATED FROM SLIDING OF HIGH DENSITY POLYETHYLENE AGAINST AIR BUBBLE SHEET OF LOW DENSITY POLYETHYLENE [PDF]
Journal of the Egyptian Society of Tribology, 2017 The present work investigates the electrostatic charge (ESC) generated from contact and separation as well as sliding of high density polyethylene (HDPE) on the air bubble sheets. They are made of low-density polyethylene (LDPE) of air-bubbles. They have
A. S. Ali, A. Alahmadi, W. Y. Ali
doaj +1 more source
Alumina and low density polyethylene composite for ballistics applications
Journal of Materials Research and Technology, 2021 The efficiency of alumina and low-density polyethylene (LDPE) composites in ballistic applications was investigated. Different concentrations of alumina were studied, 70, 75, 80, 85, 90 wt.%. The ballistic tests were carried out at subsonic speed using a
Marcio Jardim Oliveira +3 more
doaj +1 more source
Degradation of polyethylene during extrusion. II. Degradation of low‐density polyethylene, linear low‐density polyethylene, and high‐density polyethylene in film extrusion [PDF]
Journal of Applied Polymer Science, 2003 AbstractThe degradation of different polyethylenes—low‐density polyethylene (LDPE), linear low‐density polyethylene (LLDPE), and high‐density polyethylene (HDPE)—with and without antioxidants and at different oxygen concentrations in the polymer granulates, have been studied in extrusion coating processing.
Thorbjörn Andersson +2 more
openaire +1 more source
Data in Brief, 2021 This paper compiles polymer characterization data collected from polyethylene (PE) blends composed of different densities (low-density, LDPE, linear low-density, LLDPE, medium-density, MDPE, and high-density, HDPE) and post-consumer recycled polyethylene
Victor S. Cecon +3 more
doaj +1 more source