Results 81 to 90 of about 15,295,852 (197)
Quantifying the decarbonization potential of mobile heat battery in low-temperature district heating [PDF]
This research assesses the potential of a mobile thermochemical storage system, the mobile heat battery (M-HB), for decarbonizing a low-temperature district heating (DH) system in the Netherlands. The assessment is built on a case study where the M-HB is used to transport waste heat from different sources to a neighborhood interface of a DH system ...
Shuwei Wang +3 more
openaire +2 more sources
Additively manufactured AlCrFe2Ni2 with contrasting BCC/B2‐dominant and lamellar FCC + BCC/B2 microstructures exhibits the same pressure‐induced BCC/B2 → HCP transformation. Under laser heating at high pressure, HCP is destabilized, and a cubic BCC/B2 + FCC assemblage is recovered, while the lower‐scan‐speed microstructure transforms at a lower ...
Raimundas Sereika +5 more
wiley +1 more source
Impact of Hydrogen Incorporation on Electronic and Magnetic Structure of X2CrNi18‐9 Stainless Steel
Hydrogen uptake in austenitic stainless steel alters both its electronic and magnetic structure. Seebeck measurements reveal hydrogen‐induced shifts in the electronic density of states, while neutron scattering uncovers nanoscale inhomogeneities that grow upon hydrogen incorporation, with the most pronounced effect observed in the PBF as‐built state ...
Torben Tappe +9 more
wiley +1 more source
The revamping of existing high temperature district heating systems with low temperature solutions will ensure a better usage of primary energy thanks to the reduction of thermal losses through the networks and to the possibility of use low grade ...
Marco Pellegrini +3 more
core
Microstructural evolution of premium rail steel during flash butt welding (FBW), comparing physically simulated heat‐affected zones with actual weld regions. Thermal cycles induce phase transformations and microstructural heterogeneity that influence weld quality and mechanical performance. These findings provide insights into optimizing FBW parameters
Emmanoelle Cintra da Cunha Araújo +15 more
wiley +1 more source
Particle morphology controls the balance between printability and electrical connectivity in low‐temperature AgCu/Ag metallization pastes. Flake‐shaped AgCu particles form extended low‐resistance contacts, whereas spherical particles favor processability at high metal loading. Fine Ag particles further tune void filling and conductive‐network formation
O. Mhirsi +3 more
wiley +1 more source
Efficient heat distribution in solar district heating systems [Elektronisk resurs]
This paper contains a short analysis showing the main benefit for solar district heating when a novel heat distribution concept with low temperatures is applied.
Averfalk, Helge,, Werner, Sven,
core
The present work reports the microstructural, mechanical, and texture evolution of a dissimilar combination laser‐welded maraging steel with 4340 steel. This is important for aerospace applications. The demand for dissimilar welding is growing rapidly with the requirement of efficient and durable joints.
Bharat Behl +3 more
wiley +1 more source
Development of advanced low-temperature heat transfer fluids for district heating and cooling [PDF]
The feasibility of adding phase change materials (PCMs) and surfactants to the heat transfer fluids in district cooling systems was investigated. It increases the thermal capacity of the heat transfer fluid and therefore decreases the volume that needs to be pumped. It also increases the heat transfer rate, resulting in smaller heat exchangers.
openaire +2 more sources
This study explores the influences of calendering and surface treatment during direct ink writing (DIW) of thermochromic cholesteric liquid crystal (CLC) on PET nonwovens. For the PVA‐coated nonwovens, calendering reduces pore size leading to reduced ink absorption and enhanced spreading. The NeverWet‐coated nonwovens improve thermochromic responses by
Sreenivasan Sreenivasan Narayanan +3 more
wiley +1 more source

