Results 31 to 40 of about 21,302,986 (280)
About the impact behavior of woven-ply carbon fiber-reinforced thermoplastic- and thermosetting-composites: A comparative study [PDF]
This study is aimed at comparing the response of TS-based (epoxy) and TP-based (PPS or PEEK) laminates subjected to low velocity impacts. C-scan inspections showed that impact led to diamond-shaped damage resulting from different failure mechanisms ...
Vieille, Benoit +5 more
core +1 more source
Impact toughness of multilayer steel materials at low temperatures
Abstract The results of a number of studies show that there are ways to drastically change the temperature dependence of the impact strength of structural steels, which at first glance have a paradoxical character. It was established that when the test temperature decreases down to cryogenic temperatures, the work of failure of impact ...
D V Vlasova, A I Plokhikh
openaire +1 more source
Improvement of low-velocity impact and compression-after-impact performance by z-fibre pinning. [PDF]
Z-fibre® pinning is a new method of through-thickness reinforcement of laminated composites. This paper presents an experimental test and theoretical analysis on how and why these pins can improve the resistance to impact loading and post- impact ...
X. Zhang +5 more
core +1 more source
Influence of Temperature on Fracture Toughness of Jute Fiber Reinforced Unsaturated Polyester Resin [PDF]
Jute fiber reinforced unsaturated polyester resin composites (J/UP) weresubjected to low velocity impact tests in several Temperatures degree in order to study the effects of temperature variance on the intrinsic fracture toughness Gc impact properties ...
Akram R. Jabur
doaj +1 more source
Impact toughness of Al-Li system alloys at low temperatures.
Al-2.7%Li-1.2%Cu-0.8%Mg-0.1%Zr wrought alloys are heat treated to improve their impact toughness at lower temperatures, although a number of laminated cracks form in the vertical direction to the fracture surface. Low melting point elements, K and Na, are found on the fractured surface by Auger spectroscopy.
KOBAYASHI, Toshiro +2 more
openaire +2 more sources
Effect Mechanism of Curling Temperature on the Toughness of Titanium Microalloyed High-strength Steel GCL700 [PDF]
The effect of curling temperature on the mechanical properties of Ti microalloyed high-strength steels was investigated using electron backscatter diffraction, transmission electron microscopy, scanning electron microscopy and mechanical experiments.The ...
Wang Yi, Che Zhichao, Chen Yufeng, Yang Shufeng, Zhang Junfen, Xue Qihe, Li Jingshe
doaj +3 more sources
In this study, a novel multi-step heat treatment method, including intercritical annealing and tempering, is proposed to improve the low-temperature toughness of Fe-6.5Mn-0.08C medium-manganese (Mn) steel.
Seung-Hyeok Shin +3 more
doaj +1 more source
The chromium nitrides effects on duplex stainless steels low temperature impact toughness and durability were investigated. A duplex rolled ring was cut as different blocks, and different Cr2N amounts were obtained by trial heat treatments, with the solution annealing furnace temperature set at low and high levels, 1040 and 1140 °C respectively, and ...
G. Camicia +3 more
openaire +2 more sources
Microstructure and Impact Toughness of Offshore Steel [PDF]
This study focused on the effects of microstructures on the low-temperature impact toughness of directly water-quenched offshore steel. Martensite dominated the microstructure directly below the quenched surface.
Yang, T.-C. +5 more
core +1 more source
Development of TP170P Big Size High-grade Steel Gun Pipe
As the diameter of the casing in the reservoir becomes larger and larger, and the well go deeper and deeper, the demand for strength and toughness of large-diameter perforating barrel becomes stronger.
Zhou Jiaxiang +4 more
doaj

