Results 91 to 100 of about 928,972 (342)

An Inkjet‐Printed Platinum‐Based Temperature Sensing Element on Polyimide Substrates

Advanced Engineering Materials, EarlyView.
An inkjet‐printed, meander‐structured, nanoparticle platinum‐based resistive temperature sensors on polyimide substrates are demonstrated as proof‐of‐concept. Optimized sintering at 250°C enables stable conductive structures. The Pt100‐ and Pt1000‐type sensors exhibit linear resistance–temperature characteristics with stable TCR in the 20°C–80°C range,
Shawon Alam, Thomas Kister, Alexander Scholz, Sophie Sauva, Makara Lay, Tobias Kraus, Jasmin Aghassi‐Hagmann   +6 more
wiley   +1 more source

A new, non-canonical Poisson regression model for the prediction of crashes on low-volume rural roads

IATSS Research, 2012
The purpose of the study was to compare the prediction power of a simplified non-canonical Poisson crash-prediction model to other model types. The model, fitted to serious and fatal crash data from 86 two-lane low-volume rural highway segments, showed a
Abishai Polus, Moshe Cohen
doaj   +1 more source

Effects of Carbon Nanoparticles on Triboelectro‐Induced Surface Defects

Advanced Engineering Materials, EarlyView.
Carbon nanoparticles added to grease modify the electrocontact behavior. The synergy of particle concentration and electric current dominates the surface damage of metals in contact. Electrical surface damage caused by current leakage is a critical challenge in high‐performance applications such as electric vehicle (EV) drivetrains and wind turbine ...
Mohsen Tajedini, Lu Fang, Jacob Bons, Mohammad Humaun Kabir, Evan Johnson, Joe Kosmoski, Hong Liang   +6 more
wiley   +1 more source

Interactions between Molten High‐Silicon Electrical Steels and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
This study examines how several molten high‐silicon electrical steels interact with both conventional and recycled MgO–C refractories. For this, various immersion experiments are conducted. In addition to infiltration, a number of mechanisms are identified and explained that control the corrosion of the refractory material.
Lukas Neubert, Matheus Roberto Bellé, Anton Yehorov, Anhelina Mospan, Till M. J. Stadtmüller, Seetharaman Sridhar, Christos G. Aneziris, Olena Volkova   +7 more
wiley   +1 more source

Multimodal Mechanical Testing of Additively Manufactured Ti6Al4V Lattice Structures: Compression, Bending, and Fatigue

Advanced Engineering Materials, EarlyView.
In this experimental study, the mechanical properties of additively manufactured Ti‐6Al‐4V lattice structures of different geometries are characterized using compression, four point bending and fatigue testing. While TPMS designs show superior fatigue resistance, SplitP and Honeycomb lattice structures combine high stiffness and strength. The resulting
Klaus Burkart, Jonas Schmidt, Anastasiya Toenjes, Johanna Eisenträger   +3 more
wiley   +1 more source

PRAKTEK PEMBUATAN JALAN HUTAN DAN PERMASALAHANNYA DI DAERAH PROPINSI JAMBI

Jurnal Penelitian Hasil Hutan (Journal of Forest Products Research), 2017
An obseroation on road  construction practice and its problems in two logging company areas in Jambi Province was conducted in  1990. The spcific playeical condition of  the area observed is quite light  and,  therefore, the coat of road construction is ...
Djaban Tinambunan
doaj   +1 more source

Engineering geology of cinder gravel in Ethiopia: prospecting, testing and application to low-volume roads

Bulletin of Engineering Geology and the Environment, 2018
Expansion of the rural road network in Ethiopia requires the availability of low-cost materials for road construction, including capping layer and subgrade improvement, sub-base, base course, gravel wearing course and bituminised surface treatment.
G. Hearn, A. Otto, P. Greening, A. Endale, Deribachew Mezgebu Etefa   +4 more
semanticscholar   +1 more source

Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6

Advanced Engineering Materials, EarlyView.
The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter, Thomas Wegener, Andreas Schilling, Martin Fehlbier, Thomas Niendorf   +4 more
wiley   +1 more source

Bearing Capacity Assessment on low Volume Roads

IOP Conference Series: Materials Science and Engineering, 2015
A large part of Latvian road network consists of low traffic volume roads and in particular of roads without hard pavement. Unbounded pavements shows serious problems in the form of rutting and other deformations, which finally lead to weak serviceability and damage of the road structure after intensive exploitation periods.
openaire   +1 more source

Nitride‐Reinforced Metal Matrix Nanocomposite Powders Production by Plasma‐Assisted Thermochemical Treatment of Intermetallic Powders

Advanced Engineering Materials, EarlyView.
This study proposes a new methodology for producing metal matrix nanocomposites in the solid state. The process involves the plasma‐assisted thermochemical treatment of metallic alloy powders. As a proof‐of‐concept, TiN nanoparticles are synthesized directly on the surface of FeTi intermetallic powder particles, enabling the development of the ...
Deivison Daros Paim, Antônio Rogério de Souza, Tatiana Bendo, Aloisio Nelmo Klein, Rodrigo Perito Cardoso   +4 more
wiley   +1 more source