Results 51 to 60 of about 25,042,350 (333)

Sedimentation and Flow Through Porous Media: Simulating Dynamically Coupled Discrete and Continuum Phases [PDF]

open access: yes, 1995
We describe a method to address efficiently problems of two-phase flow in the regime of low particle Reynolds number and negligible Brownian motion. One of the phases is an incompressible continuous fluid and the other a discrete particulate phase which ...
A. J. C. Ladd   +44 more
core   +1 more source

Design and experimental development of a new electronically controlled cylinder lubrication system for the large two-stroke crosshead diesel engines

open access: yesInternational Journal of Engine Research, 2019
Accurate, stable and reliable lubrication for the cylinders is very important to ensure the trouble-free operation of the marine diesel engines. A new electronically controlled cylinder lubrication system has been developed to remedy the defects of the ...
Yuhai He   +3 more
semanticscholar   +1 more source

Low‐Cost, Large‐Scale Nanoporous Metals by Mechanical Alloying, Oxide Reduction, and Dealloying of Powders

open access: yesAdvanced Engineering Materials, EarlyView.
Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley   +1 more source

Positive commandable oiler for satellite bearing lubrication [PDF]

open access: yes, 1977
The results of a feasibility study showed that on-orbit commandable lubrication of ball bearings can be accomplished by direct oil application to the moving ball surfaces.
James, G. E.
core   +2 more sources

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

open access: yesAdvanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira   +4 more
wiley   +1 more source

The Helios mechanical despin drive assembly for the high-gain antenna reflector [PDF]

open access: yes, 1976
Helios is the German-American solar probe which comes within 0.31 Astronomical Units of the sun. A special thermal design and a dry lubrication system have resulted in successful operation up to now, with Helios having finished its first orbit around the
Mueller, E. J. W.
core   +1 more source

Propulsion Mechanisms for Leidenfrost Solids on Ratchets [PDF]

open access: yes, 2013
We propose a model for the propulsion of Leidenfrost solids on ratchets based on viscous drag due to the flow of evaporating vapor. The model assumes pressure-driven flow described by the Navier-Stokes equations and is mainly studied in lubrication ...
Baier, Tobias   +4 more
core   +5 more sources

Parameter optimization of a motorized spindle lubrication system using biogeography-based optimization

open access: yesAdvances in Mechanical Engineering, 2019
Using response surface methodology, two-target parameter mathematical models for a 100MD60Y4 motorized spindle are established using biogeography-based optimization.
Lixiu Zhang   +5 more
semanticscholar   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

open access: yesAdvanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti   +11 more
wiley   +1 more source

Design and control strategy of intelligent lubrication system for mine hoist head sheave

open access: yesMeitan xuebao
The sheave is an important part of a mine hoisting system. Once it fails, it will not only affect the production efficiency of coal mine, but also cause some safety risks. Poor lubrication is one of the main causes of sheave failure.
Ziming KOU, Tengyu LI, Juan WU
doaj   +1 more source

Home - About - Disclaimer - Privacy