Results 131 to 140 of about 2,700,677 (338)
Improved direct torque control using Kalman filter: application to a doubly-fed machine [PDF]
, 2009 Direct Torque Control (DTC) has been extensively researched and applied during the last two decades. However, it has only first been applied to the Brushless Doubly Fed Reluctance Machine (BDFRM) a few years ago in its basic form inheriting its intrinsic
Chaal, Hamza, Jovanovic, Milutin
core
Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6
Advanced Engineering Materials, EarlyView.The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter +4 more
wiley +1 more source
Osiris, 2010 Abstract Gottfried Wilhelm Leibniz visited the Harz Mountains more than thirty times and spent almost three full years there between 1680 and 1686. His aim was to install wind machines for draining the Harz silver mines. Despite Leibniz’s best efforts—his commitment bordered on obsession—the enterprise ultimately failed.
openaire +2 more sources
Modular switched reluctance machines to be used in automotive applications [PDF]
, 2018 In the last decades industry, including also that of electrical machines and drives, was pushed near to its limits by the high market demands and fierce competition. As a response to the demanding challenges, improvements were made both in the design and
Szabó, Loránd
core
Can Ti‐Based MXenes Serve as Solid Lubricants for Brake Applications? A Tribological Study
Advanced Engineering Materials, EarlyView.This study explores the first implementation of Ti‐based MXenes materials in brake pad friction composite material. The resulting composite material exhibits a 48% reduction in the wear rate; alongside significant improvements are observed for thermal and mechanical properties.
Eslam Mahmoud +7 more
wiley +1 more source
AIP AdvancesIn this article, the new three-phase U-shaped and V-shaped consequent-pole hybrid excited machines with separated windings (CHEPMS machine) are proposed for superconducting flywheel energy storage. The stator teeth are divided into two types.
Guangyu Qu +4 more
doaj +1 more source
High Specific Power Electrical Machines: A System Perspective [PDF]
, 2019 There has been a growing need for high specific power electrical machines for a wide range of applications. These include hybrid/electric traction applications, aerospace applications and Oil and Gas applications.
EL-Refaie, Ayman M., Osama, Mohamed
core +1 more source
Advanced Engineering Materials, EarlyView.The results demonstrate a simulation‐driven workflow that applies LSB topology optimization with additive manufacturing constraints to mission‐specific load cases, integrating European Cooperation for Space Standardization compliant verification and manufacturability to develop structurally efficient rover suspension components.
Stelios K. Georgantzinos +11 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This article presents the NFDI‐MatWerk Ontology (MWO), a Basic Formal Ontology‐based framework for interoperable research data management in materials science and engineering (MSE). Covering consortium structures, research data management resources, services, and instruments, MWO enables semantic integration, Findable, Accessible, Interoperable, and ...
Hossein Beygi Nasrabadi +4 more
wiley +1 more source
Early fault diagnosis of transformer windings based on the improved MVMD-ELM
Frontiers in Energy ResearchAiming at the problems of weak early fault characteristics of transformer windings, large noise interference and insufficient accuracy of traditional diagnostic methods, this paper proposes an early fault diagnosis method for transformer windings based ...
Qiuyang Lin +7 more
doaj +1 more source