Results 161 to 170 of about 2,330,665 (285)

Advanced Mathematical Methods in Dental Bioengineering and Biomaterials Machining. [PDF]

Biomimetics (Basel)
Duplák J, Knežo D.
europepmc   +1 more source

Detecting Anomalous Cell Behavior in Electrochemical Battery Testing Using Machine Learning

Advanced Engineering Materials, EarlyView.
Machine‐learning‐based screening enables automated identification of anomalous battery cells from complementary electrochemical tests. A curated battery database supports configuration‐aware comparison of rate‐capability and impedance data. Supervised classification of rate‐test data achieves 90% accuracy, while CNN‐VAE‐based impedance analysis reaches
Minu Rose, Sanxchep Sharma, Veit Königer, Vincent Nebel, Jonas Oehm, Christian Weisenberger, Laura Bies, Volker Knoblauch   +7 more
wiley   +1 more source

Simulation and Experimental Research on Tooth Power Skiving Cutting of Double-circular-arc Internal Gears

Jixie chuandong
A method for machining double-circular-arc internal gears using power skiving technology is proposed to address the current problems of difficulty, poor accuracy, and low efficiency in machining double-circular-arc internal gears.
Wang Feng, Yang Shufeng, Xu Wenbo, Zhang Weijie, Yu Wentao   +4 more
doaj  

Nonlinear Modeling of Surface Roughness in Turning of Nitinol: Influence of Cutting Forces, Temperature, and Negative Rake Angle Tools. [PDF]

Materials (Basel)
Zębala W, Matras A, Seltenreich M.
europepmc   +1 more source

Thermal Cycle–Microstructure–Property Relationships in Rail Steel Heat‐Affected Zone Simulated by Gleeble

Advanced Engineering Materials, EarlyView.
Microstructural evolution of premium rail steel during flash butt welding (FBW), comparing physically simulated heat‐affected zones with actual weld regions. Thermal cycles induce phase transformations and microstructural heterogeneity that influence weld quality and mechanical performance. These findings provide insights into optimizing FBW parameters
Emmanoelle Cintra da Cunha Araújo, João Marcos da Silva Nunes, Marcelly Cristiny Nunes de Carvalho, Alex Rojas, Cristie Luis Kugelmeier, Cristhian Ricardo Loayza Loayza, João Carlos Ferreira, Maria Veronica Goncalves Rodrigues, Rute Sayuri Kano, Isaac Araújo Furtado, Jacyara Dalylla da Silva Nunes, Jhonatan Peres de Sousa, Marcos Natan da Silva Lima, Eden Santos Silva, Gedeon Silva Reis, Samuel Filgueiras Rodrigues   +15 more
wiley   +1 more source

Study on Residual Stresses and Deformations in Turning of Aerospace Thin-Web Gears Considering the Initial Heat-Treatment State and Clamping Constraints. [PDF]

Materials (Basel)
Chen T, Tong S, Wang W, Li S, Xu W, Su L, Sun H, Sotova C.   +7 more
europepmc   +1 more source

Self‐Sintering Ionogel Binder for Flexible, Recyclable, and Healable Printed Giant Magnetoresistive Sensors

Advanced Functional Materials, EarlyView.
ABSTRACT Electronic waste has emerged as a major environmental challenge, driven by the massive consumption and a limited lifetime of modern electronic devices, stimulating the development of sustainable electronics. Here, an all‐biomaterial gelatin‐choline‐citric acid ([Ch][CA]) ionogel is developed as an active binder to realize self‐sintered ...
Lin Guo, Xiaotao Wang, Guannan Mu, Proloy Taran Das, Igor Veremchuk, Conrad Schubert, Aaron D. Cross, Yevhen Zabila, Xuan Peng, Larysa Baraban, Denys Makarov   +10 more
wiley   +1 more source

High-Speed Precision Machining and Surface Roughness Determination of Freeform Curves Using Galerkin-NURBS Interpolation and Jerk-Limited Trajectory Planning. [PDF]

Sensors (Basel)
Garba UH, Wang T, Tian Y, Kang J, Tian C.   +4 more
europepmc   +1 more source

Advances in Sustainable and Wearable Textile Based Soft Robotics

Advanced Functional Materials, EarlyView.
This Review examines advances in wearable textile‐based soft robotics, focusing on sustainable materials, integrated sensing, and scalable actuation. It discusses manufacturing and system integration across healthcare, assistive robotics, prosthetics, and human–machine interfaces, and highlights key challenges in circular design, including life‐cycle ...
Zahir Abbas, Marzia Dulal, Sophia K. Novoselov, Victoria K. Novoselov, Kostya S. Novoselov, Shaila Afroj, Nazmul Karim   +6 more
wiley   +1 more source

Multi-Objective Optimization of Milling Process Parameters Using MOWOA and Comprehensive Performance Evaluation via AHP-TOPSIS. [PDF]

Sensors (Basel)
Cai F, Xia R.
europepmc   +1 more source