Results 21 to 30 of about 252,830 (214)
A Simulation Model of MAG Welding.
QUARTERLY JOURNAL OF THE JAPAN WELDING SOCIETY, 2001 In the present work, a three-dimensional (3-D), non-stationary thermal model for MAG (Metal Active Gas) welding is developed. The transient temperature distribution on the base metal is numerically analyzed in order to estimate the molten pool size by using a finite difference model based on the heat flow equation, and the theoretical configuration of ...
YAMAMOTO, Takeshi +3 more
openaire +2 more sources
Cold Wire Addition in MAG Welding [PDF]
International Journal of Advanced Engineering Research and Science, 2018 This work aims to present a variation of the conventional MAG (Metal Active Gas) welding process, with the addition of a cold wire fed by a slave torch in the molten pool promoted by the electric arc originated form the main wire. Comparisons were made between traditional MAG processes with only one energized wire and the MAG-CW (MAG with addition of a
Deborah Santos +2 more
openaire +1 more source
Blowholes on Pulsed MAG welding.
QUARTERLY JOURNAL OF THE JAPAN WELDING SOCIETY, 1985 Blowholes and their formation of Pulsed MAG welding was investigated. Among welding parameters such as arc length, average current, wire extension, welding speed and shielding gases, arc length was the most important factor. The average size of blowholes was as small as 0.62 mm.
Yamada, Tadaaki, Kobayashi, Minoru
openaire +2 more sources
Mechanical characterization of a stainless steel overlapped assembly welded by MAG process
Journal of Advances in Manufacturing Engineering, 2021 MIG/MAG welding is an assembly process very commonly used in different industries. It has the advantage of being faster, especially on thicker materials, economical and suitable for welding steels. Stainless steels are very well suited for metal assembly
Mustapha Benachour +2 more
doaj
Application of switch back welding to V groove MAG welding
Welding International, 2010 The formation of stable back beads in a root pass weld during one side multi-layer welding is important to achieve high quality welded metal joints in MAG welding. The authors employed the switch back welding method for V groove joints without backing plates.
YAMANE, Satoshi +3 more
openaire +2 more sources
Gas Mixtures for Welding with Micro-Jet Cooling
Archives of Metallurgy and Materials, 2015 Welding with micro-jet cooling after was tested only for MIG and MAG processes. For micro-jet gases was tested only argon, helium and nitrogen. A paper presents a piece of information about gas mixtures for micro-jet cooling after in welding.
Węgrzyn T.
doaj +1 more source
Nanjing Hangkong Hangtian Daxue XuebaoTo further enhance the metal active gas （MAG） multi-layer welding quality of P355NL1 steel used in metro bogies， this paper conducts the MAG multi-layer welding tests of the butt joint of P355NL1 steel metro bogies， analyses the macro and micro ...
YOU Jun +3 more
doaj +1 more source
Energies, 2023 Due to the use of welded finned tubes in heat exchangers, gas blocks are characterized by very good electric energy production performance, and their reliability can reach 98%. Finned tubes used in heat exchangers are usually welded. Such tubes should be
Janusz Adamiec, Michał Urbańczyk
doaj +1 more source
Weldability of S700MC steel welded with the hybrid plasma + MAG method
Manufacturing Review, 2020 The paper describes the microstructure of welded joints produced by the plasma+MAG (Metal Active Gas) method of S700MC high yield strength steel (700 MPa). Welded joints of thermomechanical steel have been made with different values of heat input.
Skowrońska Beata +3 more
doaj +1 more source
Joule heating of solid wires in MAG welding
Welding International, 2005 Abstract There are numerous studies1–12 concerning the melting rate of welding wire and various investigations have been carried out on welding current, welding current waveform, wire extension, polarity, chemical composition, wire diameter, arc length, shielding gas composition and melting rate. Joule heating of bulk wire has been a large contributory
SHIMIZU, Hiroyuki +4 more
openaire +2 more sources