Results 131 to 140 of about 1,700 (186)

Research Progress of Magnesium Alloys and Its Alloys in Medical Applications. [PDF]

Int J Gen Med
Meng X, Liu A, Wu C, Han X, Yang Q, Qiu H, Li X, Cai M, Duan T, Wang Z.   +9 more
europepmc   +1 more source

Nanodefect-Mediated Strengthening and Deformation Mechanisms in Magnesium Alloys: A Critical Review. [PDF]

Nanomaterials (Basel)
Akçakale N, Ishtiaq M, Varol T, Rizi MS.   +3 more
europepmc   +1 more source

Dissimilar Welding of Magnesium Alloys and Aluminum Alloys by Explosive Welding. [PDF]

Materials (Basel)
Mihara-Narita M, Asai K, Sato H, Watanabe Y, Nakatsugawa I, Saito N, Chino Y.   +6 more
europepmc   +1 more source

Some of the next articles are maybe not open access.

Related searches:

Constitutive Models for AZ31 Magnesium Alloys

Key Engineering Materials, 2008
The present investigation aims at studying and modelling the flow behaviour of the AZ31 magnesium alloy by means of torsion tests performed in extended ranges of temperature and strain rates. Two types of rheological models were considered. The former is based on the power law equation, whilst the latter is based on the Sellars and Tegart approach. The
Carlo Bruni, Lorenzo Donati, Mohamad El Mehtedi, M. Simoncini   +3 more
openaire   +1 more source

Microwave-assisted magnesium phosphate coating on the AZ31 magnesium alloy

Biomedical Materials, 2017
Due to the combination of many unique properties, magnesium alloys have been widely recognized as suitable metallic materials for fabricating degradable biomedical implants. However, the extremely high degradation kinetics of magnesium alloys in the physiological environment have hindered their clinical applications.
Yufu Ren, Elham Babaie, Boren Lin, Sarit B Bhaduri   +3 more
openaire   +2 more sources

The Press Formability in Magnesium Alloy AZ31

Materials Science Forum, 2000
Formability on cylindrical deep drawing and mechanical properties at relatively low temperature was investigated for a commercially rolled AZ31 magnesium. A small punch radius, which ratio to thickness was 2.5, was adoped intentionally. At room temperature, brittle fracture occurred near the flat portion of punch shoulder like as blanking. The ratio of
Hidetoshi Somekawa, Masahide Kohzu, S. Tanabe, Kenji Higashi   +3 more
openaire   +1 more source

Citrate Gel Conversion Coating on AZ31 Magnesium Alloys

ECS Transactions, 2013
A citrate gel conversion system was developed in this study. The citrate gel, which was obtained by adding ethanol into sodium citrate aqueous solution, was dissolved in glycerin to form the conversion solution. After the consecutive steps of roll coating and heating, a citrate gel conversion coating was made on AZ31 magnesium alloys. Microstructure
Yu-Ren Chu, Chao-Sung Lin
openaire   +1 more source

Ellipsometric Characterization of AZ31 Magnesium Alloy

Materials Science Forum, 2018
Ellipsometry is a non-destructive and indirect technique able to characterize both optical and dielectric properties of thin films and bulks, besides determining the thickness of thin films. This characterization is performed by evaluating the change in the polarization state of the incident light when it interacts with the material of interest.
Darlene Souza da Silva Almeida, Ladario da Silva, Marcela Teixeira Dalboni Garcia, José Adilson de Castro, Luciano Pessanha Moreira   +4 more
openaire   +1 more source

Dynamic recrystallization in AZ31 magnesium alloy

Materials Science and Engineering: A, 2007
Abstract The effects of temperature and strain rate, as the most important thermomechanical processing (TMP) parameters, on the microstructural evolution of AZ31 magnesium alloy were studied. This was performed applying hot compression tests at a temperature range of 250–450 °C with various strain rates.
S.M. Fatemi-Varzaneh, A. Zarei-Hanzaki, H. Beladi   +2 more
openaire   +1 more source