Results 121 to 130 of about 25,849 (309)
Advanced Engineering Materials, EarlyView.This review highlights advances in lightweight, lead‐free polymer nanocomposites for diagnostic X‐ray shielding. By linking filler chemistry, dispersion, architecture, and photon interaction mechanisms, it establishes structure–performance relationships guiding material design.
Aklilu G. Messele +2 more
wiley +1 more source
Biocorrosion behaviour of magnesium alloys under pseudo-physiological conditions [PDF]
, 2006 Permanent metallic implants are widely used as hard issue replacements and cardiovascular intervention devices. However, specific drawbacks with permanent implants lead to the search for degradable metallic biomaterials.
Zhang, M. X. +3 more
core
Feasibility of Nitrogen as a Carrier Gas for Inconel Cold Spray in Hydropower Application
Advanced Engineering Materials, EarlyView.N2, despite being nearly two orders of magnitude cheaper than He, is a feasible carrier gas for cold spray Inconel coatings in hydropower repair applications when higher gas temperature and pressure are used. Reducing powder size significantly improved cavitation resistance, while the addition of fine chromium carbide particles further enhanced erosion
Tianhao Wang +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study applies machine learning regression to predict chromium layer thickness in decorative trivalent chromium electroplating, using 441 experiments from laboratory‐scale (1L) and pilot‐scale (14L) setups. Tree‐based models, particularly CatBoost, outperformed linear regression by capturing nonlinear parameter interactions (R2$R^2$ up to 0.77 ...
Christoph Baumer +4 more
wiley +1 more source
Rheo-diecasting AZ91D magnesium alloy
, 2007 Magnesium recycling has become more important in today’s environmentally aware society. To prompt the usage of recycled magnesium scrap and further improve casting structure and properties, a novel physical approach, the rheo-diecasting process (RDC ...
Wang, Y, Liu, G, Fan, Z
core
Residual Stresses Induced by Dry and Cryogenic Cooling during Machining of AZ31B Magnesium Alloy [PDF]
, 2014 The major challenge of the Mg alloys has been their unsatisfactory corrosion resistance, which can be enhanced by improving the surface integrity. Cryogenic machining, where liquid nitrogen was used during machining, has been reported to improve the ...
MARQUES, Maria José +6 more
core
Advanced Engineering Materials, EarlyView.Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş +2 more
wiley +1 more source
, 1987 This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.Sensitive thermogravimetric equipment was used to monitor the oxidation rates of A1-1 to 9% Mg alloys in 0.21 oxygen/0.79 helium mixtures with and without 0.
Silva, MP, Silva, M.P
core
Advanced Engineering Materials, EarlyView.Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal +3 more
wiley +1 more source
CORROSION BEHAVIOUR OF THE AZ31 MAGNESIUM ALLOY AND SURFACE TREATMENTS FOR ITS CORROSION PROTECTION
, 2009 Nowadays environmental conservation forces the transportation industry to manufacture lighter and low emissions transport vehicles. In this contest, magnesium alloys have found increasing attention by the automotive industry because of their low density ...
Zanotto, Federica
core