Results 121 to 130 of about 6,458,528 (295)
Prototype Patent WO2025/109237 A1 for Measuring Diffusivity and Mass Transfer in Solid Biofuels
Applied SciencesThis work focuses on testing and validating a prototype device for measuring mass transfer phenomena in biomass drying processes, patented by the Universitat Politècnica de València (UPV) and Escuela Politécnica del Litoral (ESPOL), WO2025/109237 A1. The
Ignacio Gandía-Ventura +3 more
doaj +1 more source
Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning
Advanced Engineering Materials, EarlyView.The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley +1 more source
Advanced Engineering Materials, EarlyView.Gallium microalloying redirects interfacial reactions in low‐temperature Bi–Sn solders from Cu–Sn toward Cu–Ga intermetallic formation. The resulting Cu–Ga layer suppresses intermetallic growth during thermal aging, alters fracture pathways, and improves interfacial stability.
Iva Králová +6 more
wiley +1 more source
Morphology, Transport, and Dynamics of Protein Adsorption in Open‐Cell Metal Foam
Advanced Engineering Materials, EarlyView.Stainless steel (SS) open‐cell foams are shown to adsorb more protein per unit area than previously reported 316L SS and chromium oxide surfaces under static and flow conditions. An integrated approach combining 3D pore imaging, flow simulation, and protein adsorption experiments characterizes the foam’s performance.
Chinmaya Prerana Inguva +2 more
wiley +1 more source
Impact of Hydrogen Incorporation on Electronic and Magnetic Structure of X2CrNi18‐9 Stainless Steel
Advanced Engineering Materials, EarlyView.Hydrogen uptake in austenitic stainless steel alters both its electronic and magnetic structure. Seebeck measurements reveal hydrogen‐induced shifts in the electronic density of states, while neutron scattering uncovers nanoscale inhomogeneities that grow upon hydrogen incorporation, with the most pronounced effect observed in the PBF as‐built state ...
Torben Tappe +9 more
wiley +1 more source
Zhileng xuebaoTo address the demands for high-efficiency heat transfer and compact lightweight design in space stations, a high-efficiency condensation dehumidification system utilizing copper foam and driven by a Stirling refrigerator was developed.
周汉涛, 张良, 李昊玥, 方启
doaj
Advanced Engineering Materials, EarlyView.Accelerated in situ formation of TiB and TiC in Ti–5Al–2.5Sn–B4C is driven by transient liquid phase formation, which enhances particle reactions and microstructural evolution. This process increases hardness and establishes a coupled relationship between sintering temperature and reinforcement content, strongly influencing porosity in the resulting ...
Fernando. Y. Kojima, Juliano. Soyama
wiley +1 more source
Mass Transfer Coefficient During Cathodic Protectionof Low Carbon Steel in Seawater
Al-Khawarizmi Engineering Journal, 2009 The aim of this research is to calculate mass transfer coefficient, kd, during cathodic protection of low carbon steel in neutral seawater (3.5% W/V NaCl in distilled water with pH = 7). Two types of cathodic protection were used:First: Sacrificial anode
Ameel Mohammed Rahman +2 more
doaj
Discussions on Mass Transfer Coefficient
Chemical engineering, 1966 Wakao, Noriaki, Fujishiro, Shigeru
openaire +2 more sources
Advanced Engineering Materials, EarlyView.Particle morphology controls the balance between printability and electrical connectivity in low‐temperature AgCu/Ag metallization pastes. Flake‐shaped AgCu particles form extended low‐resistance contacts, whereas spherical particles favor processability at high metal loading. Fine Ag particles further tune void filling and conductive‐network formation
O. Mhirsi +3 more
wiley +1 more source