Results 71 to 80 of about 170,570 (262)
Mass transfer coefficient for volatilization of volatile organic compounds from wastewater [PDF]
Songklanakarin Journal of Science and Technology (SJST), 2006 Volatilization of volatile organics compounds (VOCs) from wastewater is recognized as an important source that caused air pollution today. In air pollution management regarding VOCs emission to atmosphere, the amount of VOCs that released from wastewater
Intamanee, J. +3 more
doaj
Advanced Engineering Materials, EarlyView.Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi +2 more
wiley +1 more source
Zhileng xuebao, 2016 Experiments are performed in rectangular micro-channels (dH =0.293 mm) under the condition of different mass flux and heat flux to evaluate the flow boiling heat transfer characteristics with deionized water and anhydrous ethanol.
Chen Yumin, Liu Dongyao
doaj
Evaluating Energy Absorption Performance of Filled Lattice Structures
Advanced Engineering Materials, EarlyView.Maximum stress must be considered to robustly evaluate energy absorber designs. This approach was applied to compare all types of absorbers in a single Ashby diagram and determine the utility of filling lattice voids with a second material. High‐performance fillers can improve the performance of lattices that are limited by buckling or catastrophic ...
Christian Bonney +2 more
wiley +1 more source
Performance Analysis of Abradable Coating Systems for Aircraft Gas Turbines
Advanced Engineering Materials, EarlyView.Three CoNiCrAlY/YSZ/MgAl2O4 abradable liner configurations on a nickel‐superalloy are evaluated by thermal‐gradient cycling and incursion tests. Laser ablation of the bondcoat and/or Y2O3‐stabilized ZrO2 (YSZ) intermediate layer increases mechanical interlocking and bonding for thick topcoats.
Hanna Heyl +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov +4 more
wiley +1 more source
Effect of size variation on microbubble mass transfer coefficient in flotation and aeration processes. [PDF]
Heliyon, 2020 Suwartha N +4 more
europepmc +1 more source
Advanced Engineering Materials, EarlyView.Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley +1 more source
Phase Field Failure Modeling: Brittle‐Ductile Dual‐Phase Microstructures under Compressive Loading
Advanced Engineering Materials, EarlyView.The approach by Amor and the approach by Miehe and Zhang for asymmetric damage behavior in the phase field method for fracture are compared regarding their fitness for microcrack‐based failure modeling. The comparison is performed for the case of a dual‐phase microstructure with a brittle and a ductile constituent.
Jakob Huber, Jan Torgersen, Ewald Werner
wiley +1 more source
low Boiling Heat Transfer Characteristics of R290 in 5mm Small-diameter Tubes
Zhileng xuebao, 2019 The characteristics of heat transfer for R290 flow boiling in 5 mm small diameter tubes were investigated experimentally with a focus on the effects of heat flux, mass flow rate, and saturation temperature on the surface coefficient of boiling heat ...
He Kuan, Liu Jianhua, Yu Xiaoxiao
doaj