Results 171 to 180 of about 1,429,804 (373)

Enhancing Corrosion Resistance and Mechanical Strength of 3D‐Printed Iron Polylactic Acid for Marine Applications via Laser Surface Texturing

Advanced Engineering Materials, EarlyView.
Laser surface texturing significantly improves the corrosion resistance and mechanical strength of 3D‐printed iron polylactic acid (Ir‐PLA) for marine applications. Optimal laser parameters reduce corrosion by 80% and enhance tensile strength by 25% and ductility by 15%.
Mohammad Rezayat, Mojtaba Karamimoghadam, Mohammadreza Lalegani Dezaki, Ali Zolfagharian, Giuseppe Casalino, Antonio Mateo, Mahdi Bodaghi   +6 more
wiley   +1 more source

Inversion of higher-order matrix difference and differential equations through their dynamical solutions

, 1990
Julio Cesar Ruiz Claeyssen, Elisabeta Gallicchio, Marco T. Vilhena   +2 more
openalex   +1 more source

Multiscale Modeling of Process‐Induced Defects in Fused Filament Fabrication‐Printed Materials

Advanced Engineering Materials, EarlyView.
This study presents a predictive multiscale modeling tool for defect analysis of fused filament fabricated‐printed materials and their performance prediction using a mechanistic data science‐based reduced‐order modeling approach. Process‐induced defects are inherent to additively manufactured parts and significantly influence the performance of printed
Satyajit Mojumder, Derick Suarez, Trevor Abbott, Wing Kam Liu   +3 more
wiley   +1 more source

Rodrigues's Formulas for Orthogonal Matrix Polynomials Satisfying Higher-Order Differential Equations [PDF]

, 2011
Antonio J. Durán
openalex   +1 more source

Effect of Water Aging on the Mechanical Properties of Hybrid Carbon/Aramid Reinforced Thermoplastic Composites

Advanced Engineering Materials, EarlyView.
This study investigates the mechanical properties of Carbon/Aramid intraply hybrid fiber‐reinforced Elium composites under 6 months of water aging. After aging, flexural strength decreases by 25.89%, tensile strength by 4.40%, and fracture toughness by 21.56%.
Muhammed Huseyin Guzel, Gurol Onal
wiley   +1 more source

X‐Ray Computed Tomography Quantifies Primary Phases and Reveals Crack Morphology in High‐Cycle Fatigue of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
Primary phases and a fatigue crack are studied in a forged blank of an aluminum alloy using synchrotron and laboratory X‐ray computed tomography. To image the crack, the fatigue test is interrupted, and a static tensile load is applied to open the crack.
Jakob Schröder, Ying Han, Tobias Fritsch, Bardia Hejazi, Alexander Ulbricht, Birgit Skrotzki, Giovanni Bruno   +6 more
wiley   +1 more source

Invariance and commutativity properties of some classes of solutions of the matrix differential equation X(t)X'(t) = X'(t)X(t)

, 1995
Jean-Claude Evard
openalex   +1 more source

A new modified generalized Laguerre operational matrix of fractional integration for solving fractional differential equations on the half line [PDF]

, 2012
Ali H Bhrawy, Mohammed Alghamdi, Taha M. Taha   +2 more
openalex   +1 more source

From Nature to Engineering: Mortar Volume and Interfacial Mechanics in Bioinspired Ceramics

Advanced Engineering Materials, EarlyView.
Inspired by natural armors like nacre, this study explores how varying the volume fraction of the soft mortar layer impacts the interfacial strength and toughness of bioinspired ceramics. Experimental and computational analysis reveals that higher mortar volumes increase energy dissipation but reduce interfacial stiffness, offering insights for ...
Ehsan Azad, Hamidreza Yazdani Sarvestani, Behnam Ashrafi, Farjad Shadmehri, Mehdi Hojjati   +4 more
wiley   +1 more source

Note on the existence of a Ψ-bounded solution for a Lyapunov matrix differential equation [PDF]

, 2012
Aurel Diamandescu
openalex   +1 more source