Results 171 to 180 of about 2,645,922 (287)
Advanced Engineering Materials, EarlyView.Micro‐Raman spectroscopy is applied to characterize corrosion products in a recycled‐based MgO–316L steel composite anode after molten salt electrolysis. A depth‐dependent Fe–O/Fe–Al–O layer sequence of magnetite, hercynite, and an Al‐doped magnetite transition zone is identified.
Felix Drechsler +9 more
wiley +1 more source
Unsupervised gene set testing based on random matrix theory. [PDF]
BMC Bioinformatics, 2016 Frost HR, Amos CI.
europepmc +1 more source
Advanced Engineering Materials, EarlyView.A carbon‐free, as‐sintered MgO–steel cermet anode, fabricated via cold isostatic pressing using MgO–C refractory recyclate, was evaluated under laboratory‐scale K‐cryolite electrolysis at 800°C. Operation at this reduced temperature, combined with the electrolyte's limited electrical conductivity, led to an increase in cell voltage.
Farhan Hossain +7 more
wiley +1 more source
Diffusion MRI noise mapping using random matrix theory. [PDF]
Magn Reson Med, 2016 Veraart J, Fieremans E, Novikov DS.
europepmc +1 more source
Deterministic Detection of Single Ion Implantation
Advanced Engineering Materials, EarlyView.Focused ion beam implantation with high detection efficiencies will enable the rapid and scalable fabrication of advanced spin‐based technologies such as qubits. This work presents the detection efficiencies of a wide range of ions implanted into solid‐state hosts, with efficiencies of >90% recorded for ion species and substrate combinations of ...
Mason Adshead +6 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley +1 more source
Phase Field Failure Modeling: Brittle‐Ductile Dual‐Phase Microstructures under Compressive Loading
Advanced Engineering Materials, EarlyView.The approach by Amor and the approach by Miehe and Zhang for asymmetric damage behavior in the phase field method for fracture are compared regarding their fitness for microcrack‐based failure modeling. The comparison is performed for the case of a dual‐phase microstructure with a brittle and a ductile constituent.
Jakob Huber, Jan Torgersen, Ewald Werner
wiley +1 more source
Time‐Dependent Oxidation and Scale Evolution of a Wrought Co/Ni‐Based Superalloy
Advanced Engineering Materials, EarlyView.This study shows how a new wrought Co/Ni‐based superalloy resists oxidation at 800 ∘$^\circ$C. The oxide scale changes from rough, fast‐growing spinel to a dense, protective chromia–alumina layer. Atom probe analysis reveals tiny refractory‐rich bubbles at the interface that mark the transition to long‐term, diffusion‐controlled protection ...
Cameron Crabb +6 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Copper‐based composites enhanced with carbon feature convenient mechanical properties and favorable electric conductivity. Processing via deformation and thermomechanical treatments can introduce advantageous microstructures further enhancing their performance. Herein, copper–graphene powder‐based composites are directly consolidated via rotary swaging
Radim Kocich +3 more
wiley +1 more source